Abstract:Regenerative heat exchangers have disadvantages such as low heat transfer coefficient from the nozzle to the gas and high hydraulic resistance due to the design of the nozzles. Wire-mesh nozzles can eliminate these shortcomings of regenerators. Wire-mesh nozzles have low hydraulic resistance and large heat transfer surface. The process of heat and mass transfer in a regenerative heat exchanger is considered. A series of numerical simulation experiments was performed. Theoretically, the optimal configuration of the nozzle was calculated: a plain weave mesh with a wire diameter of 0.4 mm, a weaving step of 2 mm, and a step of placing nets of 1 mm. The operational modes for the regenerator are considered, taking into account the period for drying the nozzle from moisture and the maximum mass of water that can hold the nozzle without the formation of drops. Given the condensation of moisture on the nozzle, the following assumptions are made: There is no temperature and concentration inhomogeneity in the cross section of the regenerator channel; The effect of thermal conductivity in the axial direction in contact between the nozzle elements on the temperature profile of the nozzle is insignificant; The time over which the regenerator is operated between the nozzle drying periods is quite short, and the thickness of the condensate layer does not affect the hydrodynamic mode of the heat regeneration process and the value of the heat transfer coefficient. The duration of the cooling and drying period depends on the humidity of the inlet air and the area of the nozzle. This is due to the need to prevent the accumulation of moisture in the device, which can lead to the reproduction of harmful bacteria and contamination of the nozzle. In the SolidWorks Flow Simulation application, simulation experiments were performed for a regenerator model accounting for the influence of compressed air motion resulting from grouped location of the nozzle elements, and the results are shown in the figures. Comparison of the results from analytical calculations and simulation experiments showed the efficiency of the mathematical model and the possibility of its use in the design calculation of regenerators. Correlation dependences have been established to determine the heat transfer coefficient and hydraulic resistance depending on the hydrodynamic conditions. The mathematical and physical model taking into account the condensation of moisture on the nozzle has been specified. Calculations have been performed for the optimal nozzle made in the form of a plain weave mesh with a wire diameter of 0.4 mm, a weaving step of 2 mm, and a step of placing nets of 1 mm.

NUMERICAL INVESTIGATION OF HEAT TRANSFER AND PRESSURE DROP OF CROSS-FLOW WOVEN WIRE MESH HEAT EXCHANGER

Simulation of Heat Transfer Through Woven Fabrics Based on the Fabric Geometry Model

Flow and Heat Transfer Analysis of Perforated Fin in Compact Heat Exchanger

Study on the effect of three key geometric parameters of chevron corrugated brazed plate heat exchanger on the heat transfer performance

Study on the thermal performance of the cross-flow plate heat exchangers

Parameters of the plain weave meshfor the nozzle of a regenerative heat exchanger

Pore Scale Analysis for Flow and Thermal Characteristics in Metallic Woven Mesh

Performance Analysis of Woven Wire Screen Matrix Heat Exchanger Units

Presence of a porous medium and the arrangements effects on the performance of an air-cooled heat exchanger: an experimental study for heat transfer and pressure drop

Pore-scale numerical simulations of flow and convective heat transfer in a porous woven metal mesh

Numerical study of the effect of a thin wire on the thermohydraulic performance in a plate fin-and-tube heat exchanger

A numerical model of thermal analysis for woven wire screen matrix heat exchanger

The Effect of Heat Exchanger Design on Heat transfer Rate and Temperature Distribution

Three-dimensional analysis for optimizing thermo-hydrodynamic performance of heat exchangers with perforated semi-circular inserts

Experimental study on cryogenic counterflow woven-wire screen matrix heat exchanger

Characterization of internal thermohydraulic flow and heat transfer improvement in a three‐dimensional circular corrugated tube surfaces based on numerical simulation and design of experiment

Numerical Investigation Of Effect Of Tube Shape On Air-Side Heat Transfer And Pressure Drop Characteristics Of A Finned Tube Heat Exchanger

An experimental study on MWCNT–water nanofluids flow and heat transfer in double-pipe heat exchanger using porous media

Numerical investigation of the effects of geometric and fluid parameters on the thermal performance of a double -tube spiral heat exchanger with a conical turbulator

An in-depth numerical and experimental analysis of wire coil inserts: enhancing thermal performance and fluid flow characteristics in double pipe heat exchangers

Parametric Study On Flow And Heat Transfer Performance Of Multi-Flow Spiral-Wound Heat Exchanger