Abstract:In order to further improve the properties of the A356 (Al–7Si–0.3Mg) alloy, which is widely used due to its excellent properties, the effect of alloying different elements has been studied. Recently, the effect of rare earth elements on a-Al grain size and Si morphology, which play a fundamental role in determining the mechanical properties, has attracted attention and studies have focused on this area. Therefore, the effects of the addition of rare earth elements erbium (Er) and europium (Eu) to the A356 alloy at different ratios on the microstructure and mechanical properties of the as-cast and T6 heat-treated condition are investigated in this paper. Grain refinement with the addition of Er and grain coarsening with the addition of Eu were observed. The average grain size decreased by 32% and became 643 μm. On the other hand, the grain size coarsened 36% (873 μm) with the addition of 0.3 Eu to 0.3 Er wt%. The unalloyed as-cast eutectic Si length was 12.0 μm and the Si aspect ratio was 9.6. The acicular long eutectic Si phases had been modified and started to form spherical with T6 state. Although the modification effect on the eutectic Si increases with the increase in the amount of Er, the modification of Eu eutectic Si is much more effective. The most effective eutectic Si modification was achieved by the addition of 0.1 Er + 0.3 Eu wt% with heat treatment when the eutectic Si refined by 80%. The best mechanical properties were obtained with the addition of 0.1 Er with T6 state. In microstructure and fracture surface SEM analysis results, the number and size of intermetallic phases increased with the addition of alloying element. Although these acicular intermetallic phases are reduced in size by heat treatment, they were not fully spherical.

Effects of Er Additions on the Microstructure, Mechanical Properties, and Electrical Conductivity of the Al‐0.4Fe‐0.05Si Alloy

Effect of Co Addition on the Phase Structure and Magnetic Properties of Fe-Si-Al Alloys

Investigation on Microstructures and Mechanical Properties of the Hypoeutectic Al-10Si-0.8Fe- X Er Alloy

Effect of Minor Er Additions on the Microstructures and Mechanical Properties of Cast Al-Cu-Mg-Ag Alloys

Influence of Erbium and Thermal Treatments on the Microstructure and Hardness of Al-Mg-Si Alloy

Effect of Er Addition on the High Temperature Strength of Al-Si-Cu-Ni-Mg-Fe Piston Alloys

Microstructural Evolution and Mechanical Properties of Al0.3CoCrFeNiSix. High-Entropy Alloys Containing Coherent Nanometer-Scaled Precipitates

Refining Ti2AlC Particles and Improvement of Microstructure and Mechanical Properties on Ti46Al8Nb2.6C Alloy by Er Addition

Effect of Rare Earth Elements Erbium and Europium Addition on Microstructure and Mechanical Properties of A356 (Al–7Si–0.3Mg) Alloy

Influence of Er Addition on Microstructure and Mechanical Properties of As-Cast Mg-10Li-5Zn Alloy

The Effect of Grain Refinement and Precipitation Strengthening Induced by Sc or Er Alloying on the Mechanical Properties of Cast Al-Li-Cu-Mg Alloys at Elevated Temperatures

Effects of addition of Er and Zr on microstructure and mechanical properties of Al–Cu–Mn–Si–Mg alloy

Effect of Er Addition on the Microstructure, Mechanical Properties and Corrosion Behaviour of Al-Zn-Mg-Cu Alloy Manufactured by Laser Powder Bed Fusion

Correlation Between Precipitates Evolution and Mechanical Properties of Al-Sc-Zr Alloy with Er Additions

Effects of Zr,Ti and Sc Additions on the Microstructure and Mechanical Properties of Al-0.4Cu-0.14Si-0.05Mg-0.2Fe Alloys

Microstructure refinement and enhanced tensile properties of Al-11Mg2Si alloy modified by erbium

Effects of Sc addition on microstructure, phase evolution and mechanical properties of Al0.2CoCrFeNi high-entropy alloys

Enhanced Strength–Corrosion Synergy of 6061Al Casting Alloy Through Erbium Addition

Effects of Si addition on mechanical, electrical and magnetic property of Cu-10Fe alloy

Enhanced multiple precipitation and long-term stability in AlCuMgSi(Sc) alloys with Er additions

Effect of Si element on phase transformation and mechanical properties for FeCoCrNiSix high entropy alloys