Abstract:An equiatomic CoCrFeMnNi high-entropy alloy, which crystallizes in the face-centered cubic (fcc) crystal structure, was produced by arc melting and drop casting. The drop-cast ingots were homogenized, cold rolled and recrystallized to obtain single-phase microstructures with three different grain sizes in the range 4–160μm. Quasi-static tensile tests at an engineering strain rate of 10−3s−1 were then performed at temperatures between 77 and 1073K. Yield strength, ultimate tensile strength and elongation to fracture all increased with decreasing temperature. During the initial stages of plasticity (up to ∼2% strain), deformation occurs by planar dislocation glide on the normal fcc slip system, {111}〈110〉, at all the temperatures and grain sizes investigated. Undissociated 1/2〈110〉 dislocations were observed, as were numerous stacking faults, which imply the dissociation of several of these dislocations into 1/6〈112〉 Shockley partials. At later stages (∼20% strain), nanoscale deformation twins were observed after interrupted tests at 77K, but not in specimens tested at room temperature, where plasticity occurred exclusively by the aforementioned dislocations which organized into cells. Deformation twinning, by continually introducing new interfaces and decreasing the mean free path of dislocations during tensile testing (“dynamic Hall–Petch”), produces a high degree of work hardening and a significant increase in the ultimate tensile strength. This increased work hardening prevents the early onset of necking instability and is a reason for the enhanced ductility observed at 77K. A second reason is that twinning can provide an additional deformation mode to accommodate plasticity. However, twinning cannot explain the increase in yield strength with decreasing temperature in our high-entropy alloy since it was not observed in the early stages of plastic deformation. Since strong temperature dependencies of yield strength are also seen in binary fcc solid solution alloys, it may be an inherent solute effect, which needs further study.

Tensile creep properties of a CrMnFeCoNi high-entropy alloy

Elevated-temperature Deformation Mechanisms in a CrMnFeCoNi High-Entropy Alloy

Tensile creep behavior and mechanism of CoCrFeMnNi high entropy alloy

Tensile creep behavior of an equiatomic CoCrNi medium entropy alloy

Long-Term Creep Behavior of a CoCrFeNi Medium-Entropy Alloy

High temperature tensile and creep properties of CrMnFeCoNi and CrFeCoNi high-entropy alloys

Creep strength variations related to grain boundaries in the equiatomic CoCrFeMnNi high-entropy alloy

Dislocation creep behavior of CoCrFeMnNi high entropy alloy at intermediate temperatures

Creep behaviour and microstructural evolution of Al x CrMnFeCoNi high-entropy alloys

Intermediate-Temperature Creep Deformation and Microstructural Evolution of an Equiatomic FCC-Structured CoCrFeNiMn High-Entropy Alloy

Temperature Dependent Solid Solution Strengthening in the High Entropy Alloy CrMnFeCoNi in Single Crystalline State

Creep properties and deformation mechanisms of a Ni2Co1Fe1V0.5Mo0.2 medium-entropy alloy

In-situ neutron diffraction studies on high-temperature deformation behavior in a CoCrFeMnNi high entropy alloy

Precipitation and decomposition in CoCrFeMnNi high entropy alloy at intermediate temperatures under creep conditions

The influences of temperature and microstructure on the tensile properties of a CoCrFeMnNi high-entropy alloy

High-temperature deformation mechanisms and processing maps of equiatomic CoCrFeMnNi high-entropy alloy

High temperature creep of precipitation-strengthened Ni3Al-based alloy

Spherical nanoindentation creep behavior of nanocrystalline and coarse-grained CoCrFeMnNi high-entropy alloys

Nanoindentation Creep Behavior of an Al0.3CoCrFeNi High-Entropy Alloy

Long-Term Creep Behavior of a CoCrFeNiMn High-Entropy Alloy