Abstract:The use of high strength low alloy steels provides several potential advantages including lower weight, lower manufacturing costs, and ease of handling and transport. The progress in steel manufacturing technology has continually called for new developments in welding processes and consumables to produce weld metal deposits with mechanical properties essentially equivalent to the base metal. Controlling the weld metal microstructures as well as raising the welding productivity is critical factor for the development of weld metal of high strength steel to secure satisfactory mechanical properties and to reduce production costs. In order to meet the demand to apply 1000 MPa class steel to the fabrication of large scale steel structures, a weld wire for the 1000 MPa class steel has been under development to obtain the required strength and toughness, which depend primarily on the microstructure. In this work, the effects of shielding gas composition on the microstructure and properties of 1000 MPa grade deposited metals produced by metal active gas (MAG) welding have been investigated. The shielding gas employed was a mixture of argon (Ar) and carbon dioxide (CO2) (5%similar to 30%), and the weld heat input was 13 kJ/cm. The properties of deposited metal with shielding gas of 80%Ar+20%CO2 is the best, the yield strength is 980 MPa, meanwhile, its Charpy absorbed energy at room temperature and -40 degrees C are 72.6 and 52 J, respectively. The results show that the microstructure of the deposited metal, consisting primary of low carbon martensite and a few parallel bainite plate, became more interweaved bainitic packets as the CO2 content of the shielding gas was increased. The initial bainite nucleated at austenite grain boundaries and subsequent bainite plates can form at the oxide inclusions of intragranular, which presented an intersected configuration and the microstructure was refined. The content of bainite palte and distribution morphology of martensite/bainite is the intrinsic reason attributed to mechanical properties of deposited metals. The content of bainite for deposited metal has an optimal proportion and more isn't necessarily better. It was also found that the area fraction, the size and the compositions of oxide inclusions in deposited metals were changed with increasing CO2 content. The deposited metal as using 70%Ar+30%CO2 has the minimum toughness because more large size oxide inclusions formed which are known to be harmful to the toughness.

Effect of N2 content in shielding gas on formation quality and microstructure of high nitrogen austenitic stainless steel fabricated by wire and arc additive manufacturing

Manufacturing high nitrogen austenitic stainless steels by pressurized induction furnace

Influence of shielding gas nitrogen content on the microstructure and mechanical properties of Cu-reinforced maraging steel fabricated by wire arc additive manufacturing

Microstructure and Mechanical Properties of Welding Metal with High Cr-Ni Austenite Wire Through Ar-He-N-2 Gas Metal Arc Welding

Microstructures and Properties of Wire-Arc Additively Manufactured 5356 Aluminium Alloy Protected by Different Proportions of Nitrogen and Argon

Gas metal arc welding of high nitrogen stainless steel with Ar–N2-O2 ternary shielding gas

Effect of Nitrogen‐Added Shielding Gas on Microstructure Evolution of Welded Joints by Gas Tungsten Arc Welding Process in Duplex Stainless Steel 2205

Effects of Nitrogen Element on Microstructure and Pitting Corrosion Resistance of Duplex Stainless Steel Welded Joints

Dissimilar welding of high nitrogen stainless steel and low alloy high strength steel under different shielding gas composition: Process, microstructure and mechanical properties

Effects of Ar-N 2 -He shielding gas on microstructure, mechanical properties and corrosion resistance of the Laser-MIG additive manufacturing 316L stainless steel

Optimization of shielding gas composition in high nitrogen stainless steel gas metal arc welding

System study of the formability, nitrogen behaviour and microstructure features of the CMT wire and arc additively manufactured high nitrogen Cr-Mn stainless steel

Effect of nitrogen content on microstructure and mechanical properties of duplex stainless steels via wire arc additive manufacturing

Effect of shielding gas on MIG welding performance with austenitic wire

Droplet transfer behavior and weld formation of gas metal arc welding for high nitrogen austenitic stainless steel

Effect of nitrogen content on microstructure, mechanical properties, and corrosion behaviour of coarse-grained heat-affected zone of nitrogen-containing austenitic stainless steel

EFFECT OF SHIELDING GAS ON MICROSTRUCTURE AND PERFORMANCE OF 1000 MPa GRADE DEPOSITED METALS

Investigation of 300M ultra-high-strength steel deposited by wire-based gas metal arc additive manufacturing

Influence of Shielding Gas on Microstructure and Properties of GMAW DSS2205 Welded Joints

Influence of Shielding Gas Composition on Microstructure Characteristics of 1000 MPa Grade Deposited Metals

Nitrogen Effects in Additively Manufactured Martensitic Stainless Steels: Conventional Thermal Processing and Comparison with Wrought