Abstract:The use of high strength low alloy steels provides several potential advantages including lower weight, lower manufacturing costs, and ease of handling and transport. The progress in steel manufacturing technology has continually called for new developments in welding processes and consumables to produce weld metal deposits with mechanical properties essentially equivalent to the base metal. Controlling the weld metal microstructures as well as raising the welding productivity is critical factor for the development of weld metal of high strength steel to secure satisfactory mechanical properties and to reduce production costs. In order to meet the demand to apply 1000 MPa class steel to the fabrication of large scale steel structures, a weld wire for the 1000 MPa class steel has been under development to obtain the required strength and toughness, which depend primarily on the microstructure. In this work, the effects of shielding gas composition on the microstructure and properties of 1000 MPa grade deposited metals produced by metal active gas (MAG) welding have been investigated. The shielding gas employed was a mixture of argon (Ar) and carbon dioxide (CO2) (5%similar to 30%), and the weld heat input was 13 kJ/cm. The properties of deposited metal with shielding gas of 80%Ar+20%CO2 is the best, the yield strength is 980 MPa, meanwhile, its Charpy absorbed energy at room temperature and -40 degrees C are 72.6 and 52 J, respectively. The results show that the microstructure of the deposited metal, consisting primary of low carbon martensite and a few parallel bainite plate, became more interweaved bainitic packets as the CO2 content of the shielding gas was increased. The initial bainite nucleated at austenite grain boundaries and subsequent bainite plates can form at the oxide inclusions of intragranular, which presented an intersected configuration and the microstructure was refined. The content of bainite palte and distribution morphology of martensite/bainite is the intrinsic reason attributed to mechanical properties of deposited metals. The content of bainite for deposited metal has an optimal proportion and more isn't necessarily better. It was also found that the area fraction, the size and the compositions of oxide inclusions in deposited metals were changed with increasing CO2 content. The deposited metal as using 70%Ar+30%CO2 has the minimum toughness because more large size oxide inclusions formed which are known to be harmful to the toughness.

Influence of Shielding Gas Composition on Microstructure Characteristics of 1000 MPa Grade Deposited Metals

EFFECT OF SHIELDING GAS ON MICROSTRUCTURE AND PERFORMANCE OF 1000 MPa GRADE DEPOSITED METALS

Influence of Carbon Content on Microstructure and Mechanical Properties of 1000 MPa Deposited Metal by Gas Metal Arc Welding

Effect of carbon content on strength and toughness of deposited metal for 1000 MPa-grade high-strength welding wire

Effect of Cu Content on Microstructure and Mechanical Properties for High-Strength Deposited Metals Strengthened by Nano-Precipitation

The Effect of Nickel Contents on the Microstructure Evolution and Toughness of 800 MPa Grade Low Carbon Bainite Deposited Metal

Effect of the Temperature of Post Weld Heat Treatment on Microstructure and Performance of Weld Metal for 1 000 MPa Grade High Strength Steel

Effect of Welding Processes with High Heat Input on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of a High-Strength High-Toughness Steel

Effect of N2 content in shielding gas on formation quality and microstructure of high nitrogen austenitic stainless steel fabricated by wire and arc additive manufacturing

Effect of shielding gas on MIG welding performance with austenitic wire

Influence of Shielding Gas on Microstructure and Mechanical Properties of Laser Welded–brazed Al/steel Lapped Joint

Microstructure and Mechanical Properties of the Ternary Gas Shielded Narrow-Gap GMA Welded Joint of High-Strength Steel

The effect of welding speed on the microstructure, mechanical properties, and fatigue failure of Q690D high-strength steel

Effect of Heat Input on the Metal Microstructure and Mechanical Properties of Q960 High‐Strength Steel Solid Core Welding Wire

Influence of Shielding Gas on Microstructure and Properties of GMAW DSS2205 Welded Joints

Influence of shielding gas nitrogen content on the microstructure and mechanical properties of Cu-reinforced maraging steel fabricated by wire arc additive manufacturing

Effect of the Shielding Gas and Heat Treatment in Inconel 625 Coatings Deposited by GMAW Process

Microstructure and Mechanical Properties of Welded Joints of 440 MPa Grade Marine Engineering Steel under Different Welding Methods

Effects of Shielding Gas on GMAW of 10ni5crmov HSLA Steel Using High Cr-Ni Austenitic Wire

Investigation of 300M ultra-high-strength steel deposited by wire-based gas metal arc additive manufacturing

Effect of Heat Input on Microstructure and Performance of Welded Joint in 1 000 MPa Grade Steel for Construction Machinery