Abstract:Titanium alloy Ti6Al4V has been recognized for its high strength-to-weight ratio. Extensive deformation study has been conducted; however, defects like strain-induced porosities, non-uniform microstructure, etc., are observed during thermomechanical processing. So, optimization of thermomechanical processing parameters is highly essential to avoid the recurrence of these kinds of defects. Characterization of defects noticed in hot-rolled ring sample was carried out and a detailed deformation study has been conducted to understand the generation of such defects to avoid their occurrence. The study has been conducted in the temperature range of 800-1050 °C and strain rate of 0.001 to 10 s −1 using a Gleeble 3800 thermomechanical simulator. Microstructural mapping of the deformed Ti6Al4V is carried out. Workability by hot deformation is explained through processing maps. As per the efficiency of power dissipation maps, the maximum efficiency of 65-70 % is obtained in the temperature range of 825-900 °C and strain rate 10 −3 to 10 −2.5 s −1 up to 0.4 strains. Arrhenius equations are used to calculate the activation energy of hot deformation and an average of 620.62 kJ/mol was obtained for the temperature range of 750-950 oC. Prediction capability of constitutive models like the modified Johnson–Cook (m-JC) model and artificial neural network (ANN) was verified for deformation behavior. ANN model is found to give the best fit with an absolute average error (AARE) of 0.0417 and correlation coefficient ( R ) 0.9985. Hot rolling was also conducted at different temperatures of 800-950 °C in the intervals of 50 °C up to 50 % reduction. Microstructure obtained through hot compression and hot rolling is discussed. Specimen hot compressed at 800 °C and strain rates of 0.001, 0.01, 0.1, 1 and 10 s −1 showed strain-induced porosities along the grain boundaries. Similarly, hot-rolled samples at 800 °C showed the presence of strain-induced porosities.

Structure of sheet blanks from VT6S titanium alloy after local deformation during pulse heating by electric current

Effect of pulsed electric heating local deformation mode on structure of blanks made of titanium VT6S alloy

Constitutive Model and Microstructure Evolution of a Novel TG6 High-Temperature Titanium Alloy during Hot Deformation

Superplastic Behavior and Microstructural Features of the VT6 Titanium Alloy with an Ultrafine-Grained Structure during Upsetting

Micromechanical testing and microstructure analysis of as-welded and post-weld heat-treated Ti-6Al-4V alloy

Microstructure changes during non-conventional heat treatment of thin Ni–Ti wires by pulsed electric current studied by transmission electron microscopy

Local softening deformation and phase transformation induced by electric current in electrically-assisted micro-compression of Ti–6Al–4V alloy

Enhancement of Ductility, Weakening of Anisotropy Behavior and Local Recrystallization in Cold-Rolled Ti-6Al-4V Alloy Strips by High-Density Electropulsing Treatment

Microstructure Evolution and Deformation Mechanisms of As-Cast Antibacterial Ti6Al4V-5Cu Alloy for Isothermal Forging Process

Role of the Pulse Current Duty Cycle during Titanium Tension

RETRACTED: Microstructure, Properties and Temperature Evolution of Electro-Pulsing Treated Functionally Graded Ti–6Al–4V Alloy Strip

On Strain-Hardening Behavior and Ductility of Laser Powder Bed-Fused Ti6Al4V Alloy Heat-Treated above and below the β-Transus

Hot Tensile Deformation Behavior of Ti-6Al-4V Titanium Alloy Made by Laser Melting Deposition

Electron Beam Welding Process for Ti6Al-4V Titanium Alloy

Effect of DC Micro-Pulsing on Microstructure and Mechanical Properties of TIG Welded Ti-6Al-4V

Influence of the Coarse Grain Structure of a Titanium Alloy Ti-4Al-3V Formed by Wire-Feed Electron Beam Additive Manufacturing on Strain Inhomogeneities and Fracture

In-situ tensile deformation behavior of powder metallurgy Ti6Al4V alloys

In-situ investigation into the deformation behavior of Ti-6Al-4V processed by laser powder bed fusion

Hot Workability and Microstructure Control of Ti6Al4V Alloy

Formation of the Structure, Phase Composition, and Properties in High-Strength Titanium Alloy upon Isothermal and Thermomechanical Treatment

Influence of structure on mechanisms of VT22I titanium alloy deformation during implementation of shape memory effect