Abstract:The flow behaviour of AA2060 Al alloy under warm/hot deformation conditions is complicated because of its dependency on strain rates (ε˙), strain (ε), and deformation modes. Thus, it is crucial to reveal and predict the flow behaviours of this alloy at a wide range of temperatures (T) and ε˙ using different constitutive models. Firstly, the isothermal tensile tests were carried out via a Gleeble-3800 thermomechanical simulator at a T range of 100, 200, 300, 400, and 500 °C and ε˙ range of 0.01, 0.1, 1, and 10 s-1 to reveal the warm/hot flow behaviours of AA2060 alloy sheet. Consequently, three phenomenological-based constitutive models (L-MJC, S1-MJC, S2-MJC) and a modified Zerilli-Armstrong (MZA) model representing physically based constitutive models were developed to precisely predict the flow behaviour of AA2060 alloy sheet under a wide range of T and ε˙. The predictability of the developed constitutive models was assessed and compared using various statistical parameters, including the correlation coefficient (R), average absolute relative error (AARE), and root mean square error (RMSE). By comparing the results determined from these models and those obtained from experimentations, and confirmed by R, AARE, and RMSE values, it is concluded that the predicted stresses determined from the S2-MJC model align closely with the experimental stresses, demonstrating a remarkable fit compared to the S1-MJC, L-MJC, and MZA models. This is because of the linking impact between softening, the strain rate, and strain hardening in the S2-MJC model. It is widely known that the dislocation process is affected by softening and strain rates. This is attributed to the interactions that occurred between ε and ε˙ from one side and between ε, ε˙, and T from the other side using an extensive set of constants correlating the constitutive components of dynamic recovery and softening mechanisms.

Experimental and numerical investigation of sheet metal failure based on Johnson-Cook model and Erichsen test over a wide range of temperatures

Calibration of the Johnson–Cook model at high temperatures for an Ultra-High Strength CrNiMoV Steel

Parametric study of aluminum bar shearing using Johnson-Cook material modeling

Experimental Development of Johnson–Cook Strength Model for Different Carbon Steel Grades and Application for Single‐Pass Hot Rolling

Experimental and Simulation Studies of Erichsen Cupping Test on Aluminum(7075) Sheet Using Damage Theory

INVESTIGATION INTO THE THERMAL DEFORMATION BEHAVIOR AND THE ESTABLISHMENT OF A CONSTITUTIVE RELATIONSHIP FOR Mn-Cr-Ni-Mo STEEL

Study on constitutive relationship of 6061 aluminum alloy based on Johnson-Cook model

Thermo-mechanical finite element analysis of the AA5086 alloy under warm forming conditions

Research on Johnson–Cook Constitutive Model of γ-TiAl Alloy with Improved Parameters

A modified Johnson-Cook model considering strain softening of A356 alloy

An Enhanced Johnson–Cook Model for Hot Compressed A356 Aluminum Alloy

A Comparative Study on Modified Johnson–Cook and Arrhenius-Type Constitutive Models to Predict the Hot Deformation Behaviour of Molybdenum-Hafnium-Carbide Alloy

The Comparation of Arrhenius-Type and Modified Johnson–Cook Constitutive Models at Elevated Temperature for Annealed TA31 Titanium Alloy

Modeling of constitutive behavior and ductile fracture of AA5A06 aluminum alloy sheet in warm hydroforming process

Modelling the Flow Behaviour of Al Alloy Sheets at Elevated Temperatures Using a Modified Zerilli-Armstrong Model and Phenomenological-Based Constitutive Models

Mechanical Properties and Fracture Toughness Prediction of Ductile Cast Iron under Thermomechanical Treatment

Numerical Modeling of Magnesium Alloy Sheet Metal Forming at Elevated Temperature

A Modified Johnson–Cook Model for Modeling AA6061-T6 under Different Temperatures Considering Ductile Fracture

Analysis of the High Temperature Plastic Deformation Characteristics of 18CrNi4A Steel and Establishment of a Modified Johnson–Cook Constitutive Model

Numerical prediction and experimental validation of forming limit curves of laminated half-hard aluminum sheets

A Generalized Stress State and Temperature Dependent Damage Indicator Framework for Ductile Failure Prediction in Heat-Assisted Forming Operations