Abstract:Mechanical stacking of a thin film perovskite-based solar cell on top of crystalline Si (cSi) solar cell has recently attracted a lot of attention as it is considered a viable route to overcome the limitations of cSi single junction power conversion efficiency. Effective light management is however crucial to minimize reflection or parasitic absorption losses in either the top cell or in the light in-coupling of the transmitted light to the bottom sub-cell. The study here is focused on calculating an optimum performance of a four-terminal mechanically stacked tandem structure by varying the optical property and thickness of the spacer between top and bottom sub-cells. The impact of the nature of the spacer material, with its refractive index and absorption coefficient, as well as the thickness of that layer is used as variables in the optical simulation. The optical simulation is done by using the transfer matrix-method (TMM) on a stack of a semi-transparent perovskite solar cell (top cell) mounted on top of a cSi interdigitated back contact (IBC) solar cell (bottom cell). Two types of perovskite absorber material are considered, with very similar optical properties. The total internal and external short circuit current (Jsc) losses for the semitransparent perovskite top cell as a function of the different optical spacers (material and thickness) are calculated. While selecting the optical spacer materials, Jsc for both silicon (bottom cell) and perovskite (top cell) were considered with the aim to optimize the stack for maximum overall short circuit current. From these simulations, it was found that this optimum in our four-terminal tandem occurred at a thickness of the optical spacer of 160 nm for a material with refractive index n = 1.25. At this optimum, with a combination of selected semi-transparent perovskite top cell, the simulated maximum overall short circuit current (Jsc-combined, max) equals to 34.31 mA/cm². As a result, the four-terminal perovskite/cSi multi-junction solar cell exhibits a power conversion efficiency (PCE) of 25.26%, as the sum of the perovskite top cell PCE = 16.50% and the bottom IBC cSi cell PCE = 8.75%. This accounts for an improvement of more than 2% absolute when compared to the stand-alone IBC cSi solar cell with 23.2% efficiency.

Investigation of optical and electrical properties of novel 4T all perovskite tandem solar cell

A monolithic all-perovskite tandem solar cell with 2-T, 3-T and 4-T architecture integrated

Theoretical Analysis of All‐Inorganic Wide Bandgap Perovskite /Sn‐Based Narrow Bandgap Perovskite Tandem Solar Cells

Device simulation and experimental validation of perovskite-cadmium telluride 4T tandem solar cell

Numerical study of flexible perovskite/Si tandem solar cell using TCAD simulation

Optical management of spacer layer of high-performance four-terminal perovskite/silicon tandem solar cells

Surface Reconstruction for Stable Monolithic All‐Inorganic Perovskite/Organic Tandem Solar Cells with over 21% Efficiency

Performance and optimization study of selected 4-terminal tandem solar cells

Enhanced efficiency of carbon based all perovskite tandem solar cells via cubic plasmonic metallic nanoparticles with dielectric nano shells

Efficiency Boosting of 4-T Bifacial Dual-Textured Perovskite/Perl Silicon Tandem Solar Cells: Process and Device TCAD Simulation Study

Textured Perovskite/Silicon Tandem Solar Cells Achieving Over 30% Efficiency Promoted by 4-Fluorobenzylamine Hydroiodide

Light Management Enhancement for Four-Terminal Perovskite-Silicon Tandem Solar Cells: The Impact of the Optical Properties and Thickness of the Spacer Layer between Sub-Cells

Dual‐Site Anchors Enabling Vertical Molecular Orientation for Efficient All‐Perovskite Tandem Solar Cells

High-Performance Flexible All-Perovskite Tandem Solar Cells with Reduced VOC-Deficit in Wide-Bandgap Subcell

Four‐Terminal Perovskite‐CdSeTe Tandem Solar Cells: From 25% toward 30% Power Conversion Efficiency and Beyond

Design and simulation of three-junction all perovskite tandem solar cells: A path to enhanced photovoltaic performance

All-perovskite tandem solar cells with 3D/3D bilayer perovskite heterojunction

Quasi-conformal Monolithic N-I-p Perovskite/c-Si Tandem Solar Cells with Light Management Strategies Exceed 28% Efficiency

Study and Optimization of a New Perovskite Solar Cell Structure Based on the Two Absorber Materials Cs2TiBr6 and MASnBr3 Using SCAPS 1D

Exploring the Potential of Lead-Free Perovskite/ Kesterite Double Absorber Structure With Diverse Transport Layer Materials to Enhance Tandem Solar Cell Performance

High-Efficiency Electron Transport Layer-Free Perovskite/GeTe Tandem Solar Cell: Numerical Simulation