Abstract:Mechanical stacking of a thin film perovskite-based solar cell on top of crystalline Si (cSi) solar cell has recently attracted a lot of attention as it is considered a viable route to overcome the limitations of cSi single junction power conversion efficiency. Effective light management is however crucial to minimize reflection or parasitic absorption losses in either the top cell or in the light in-coupling of the transmitted light to the bottom sub-cell. The study here is focused on calculating an optimum performance of a four-terminal mechanically stacked tandem structure by varying the optical property and thickness of the spacer between top and bottom sub-cells. The impact of the nature of the spacer material, with its refractive index and absorption coefficient, as well as the thickness of that layer is used as variables in the optical simulation. The optical simulation is done by using the transfer matrix-method (TMM) on a stack of a semi-transparent perovskite solar cell (top cell) mounted on top of a cSi interdigitated back contact (IBC) solar cell (bottom cell). Two types of perovskite absorber material are considered, with very similar optical properties. The total internal and external short circuit current (Jsc) losses for the semitransparent perovskite top cell as a function of the different optical spacers (material and thickness) are calculated. While selecting the optical spacer materials, Jsc for both silicon (bottom cell) and perovskite (top cell) were considered with the aim to optimize the stack for maximum overall short circuit current. From these simulations, it was found that this optimum in our four-terminal tandem occurred at a thickness of the optical spacer of 160 nm for a material with refractive index n = 1.25. At this optimum, with a combination of selected semi-transparent perovskite top cell, the simulated maximum overall short circuit current (Jsc-combined, max) equals to 34.31 mA/cm². As a result, the four-terminal perovskite/cSi multi-junction solar cell exhibits a power conversion efficiency (PCE) of 25.26%, as the sum of the perovskite top cell PCE = 16.50% and the bottom IBC cSi cell PCE = 8.75%. This accounts for an improvement of more than 2% absolute when compared to the stand-alone IBC cSi solar cell with 23.2% efficiency.

Optical management of spacer layer of high-performance four-terminal perovskite/silicon tandem solar cells

Light Management Enhancement for Four-Terminal Perovskite-Silicon Tandem Solar Cells: The Impact of the Optical Properties and Thickness of the Spacer Layer between Sub-Cells

Optical Design of Monolithic Two-Terminal Perovskite/Si Tandem Solar Cells for Efficient Photon Management

The optimization of CsPbIBr2 top sub-cells for the application in monolithic all-perovskite tandem solar cells

Quasi-conformal Monolithic N-I-p Perovskite/c-Si Tandem Solar Cells with Light Management Strategies Exceed 28% Efficiency

Phase-Stable Wide-Bandgap Perovskites for Four-Terminal Perovskite/Silicon Tandem Solar Cells with over 30% Efficiency.

Efficient and Stable Perovskite/Silicon Tandem Solar Cells Modulated with Triple‐Functional Passivator

Surface Reconstruction for Stable Monolithic All‐Inorganic Perovskite/Organic Tandem Solar Cells with over 21% Efficiency

Efficient Monolithic Perovskite/Silicon Tandem Photovoltaics

Theoretical Analysis of All‐Inorganic Wide Bandgap Perovskite /Sn‐Based Narrow Bandgap Perovskite Tandem Solar Cells

Regulating Charge Carrier Recombination in the Interconnecting Layer to Boost the Efficiency and Stability of Monolithic Perovskite/Organic Tandem Solar Cells

Device simulation and experimental validation of perovskite-cadmium telluride 4T tandem solar cell

A Scalable Method for Fabricating Monolithic Perovskite/silicon Tandem Solar Cells Based on Low-Cost Industrial Silicon Bottom Cells

Multifunctional Buffer Layer Engineering for Efficient and Stable Wide‐Bandgap Perovskite and Perovskite/Silicon Tandem Solar Cells

Textured Perovskite/Silicon Tandem Solar Cells Achieving Over 30% Efficiency Promoted by 4-Fluorobenzylamine Hydroiodide

Perovskite‐Based Tandem Solar Cells: Get the Most Out of the Sun

Enhanced Efficiency of Semitransparent Perovskite Solar Cells via Double-Sided Sandwich Evaporation Technique for Four Terminal Perovskite-Silicon Tandem Application

Efficient and Reproducible Monolithic Perovskite/Organic Tandem Solar Cells with Low-Loss Interconnecting Layers

Ameliorating Properties of Perovskite and Perovskite–Silicon Tandem Solar Cells via Mesoporous Antireflection Coating Model

Performance and optimization study of selected 4-terminal tandem solar cells

Molecular Synergistic Effect for High Efficiency Monolithic Perovskite/Perovskite/Silicon Triple‐Junction Tandem Solar Cells