Abstract:To reduce the "shuttle effects" of lithium polysulfides (LIPs) and the lithium dendrites in Li-S batteries, the separator modified by hollow carbon material was prepared by the simple scraping method. It can be found from the contact angle tests that the layers formed by the porous carbon of uniform width exhibited both stronger attractions to LIPs and better permeability of electrolytes than the bare polypropylene (PP) separator. Permeation tests further showed an effective block over LIPs by the modification layers. Cathode symmetrical batteries with Celgard 3501 separator were assembled and the current response tests implied a conversion of LIPs to Li2S catalyzed by hollow carbon materials. Lithium symmetrical batteries with modified separators were assembled and the voltage-time profile of charge-discharge processes showed better stability owing to the prevention of lithium dendrites. The Li-S batteries were assembled with sulfur loading of 1.8-2.0 mg.cm(-2) and with the bare PP, single-side modified, and double-side modified separators. Calculations of the diffusion coefficient of lithium-ion from galvanostatic intermittent titration technique (GITT) tests and Nyquist plots both indicated the faster ion transportation for the modified separators. Smaller semicircles for impedance were also found in the plots. Nyquist plots after the 1st, 5th, 10th, 50th, and 100th cycles were analyzed to show a stable diffusion behavior of lithium ions, which should be caused by the multichannel from hollow carbon material to provide more paths for Li+ ion transportation. Li-S batteries with double-side modified separators presented a high specific capacity of 1 035 mAh.g(-1) in the first cycle and 500 mAh.g(-1) after 700 cycles at the current density of 0.2C, 630 mAh.g(-1) after 100 cycles at 1C, and 505 mAh.g(-1) after 100 cycles at 2C. The rate performance also behaved superior to the cells with bare PP as the separator. The cell assembled with higher sulfur content (3.2 mg.cm(-2)) also presented the reverse specific capacity of 500 mAh.g(-1) at 0.2C. These battery performances could be ascribed to the porous hollow carbon materials for their adsorption and conversion of LIPs and their prevention of dendrites. Thus, the physicochemical interaction between hollow carbon and LIPs effectively alleviates the shuttle effect and the bifunctional modification of the separator could prevent the growth of lithium dendrites to improve the safety of the Li-S batteries.

Decoration of indium tin oxide nanoparticles with different crystal structures and morphologies on polypropylene separator for Li‐S battery

Suppression Of Polysulfide Shuttling With A Separator Modified Using Spontaneously Polarized Bismuth Ferrite For High Performance Lithium-Sulfur Batteries

Empowering polypropylene separator with enhanced polysulfide adsorption and reutilization ability for high-performance Li-S batteries

Perovskite Lithium Lanthanum Titanate-Modified Separator as Both Adsorbent and Converter of Soluble Polysulfides toward High-Performance Li-S Battery

Polyaniline-Coated Cobalt–Iron Oxide Composites Modified Separator for High Performance Lithium–Sulfur Batteries

Effect of SiO2 Content on Performance of Polypropylene Separator for Lithium‐ion Batteries

Anions‐Trappable Hollow Mesoporous Nanoparticle Coating Enables High‐Performance and Safe Lithium Metal Batteries

Novel Bifunctional Separator with a Self-Assembled FeOOH/Coated g-C 3 N 4 /KB Bilayer in Lithium–Sulfur Batteries

Titanium-Containing Metal–Organic Framework Modified Separator for Advanced Lithium–Sulfur Batteries

SiO 2 blending polyetherimide separator modified with acetylene black/polyvinylpyrrolidone coating layer to enhance performance for lithium‐sulfur batteries

The Electrostatic Attraction and Catalytic Effect Enabled by Ionic–Covalent Organic Nanosheets on MXene for Separator Modification of Lithium–Sulfur Batteries

Binder‐Free TiO2‐Coated Polypropylene Separators for Advanced Lithium‐Ion Batteries

A Separator with Double Coatings of Li<sub>4</sub>Ti<sub>5</sub>O<sub>12</sub> and Conductive Carbon for Li-S Battery of Good Electrochemical Performance

In Situ Self‐Polymerization of Thioctic Acid Enabled Interphase Engineering Towards High‐Performance Lithium–Sulfur Battery

A viscous oligomer multifunctional separator coating to enable high specific energy lithium-sulfur battery

Preparation and Performance of Silica/polypropylene Composite Separator for Lithium-Ion Batteries

A Trifunctional Separator Based on a Blockage-Adsorption-Catalysis Synergistic Effect for Li-S Batteries

Accelerating catalytic conversion and chemisorption of polysulfides for advanced Li-S batteries from incorporating Fe0.64Ni0.36@Co5.47N hetero-nanocrystals into boron carbonitride nanotubes

Application of Double-Side Modified Separator with Hollow Carbon Material in High-Performance Li-S Battery

Towards High-performance Lithium-Sulfur Batteries: the Modification of Polypropylene Separator by 3D Porous Carbon Structure Embedded with Fe3C/Fe Nanoparticles

Well-Dispersed Ov-NiCo2O4 Nanospheres Modified Separator for Li-S Batteries