Abstract:Commercial application of Li–S batteries is greatly restricted by their unsatisfactory cycle retention and poor cycling life originating from the lithium polysulfide (LiPS) shuttling effect and sluggish sulfur redox kinetics. Various strategies have been proposed to boost the performances of Li–S batteries, including nanostructured sulfur composites, functional separators/interlayers, electrode/electrolyte additives, and so on. However, how to combine two or more strategies to efficiently settle these challenging issues confronted by Li–S batteries is in desperate need. Here, we demonstrate a powerful combined strategy of introducing novel 3D WS2/carbon nanotube (CNT) networks built by hybridization of 1D CNTs with 2D WS2 into Li–S batteries, simultaneously serving as a functional cathode additive and separator coating. Such 3D WS2/CNTs networks with abundant edge sites, a large active surface, and a fast electron pathway twice perform functions from the cathode side and separator surface: (1) to suppress polysulfide diffusion through a physical barrier and chemical interactions; (2) to accelerate LiPS conversion reactions; and (3) to enhance conductivity for better sulfur reactivation and high utilization. As a result, the as-built WS2/CNTs-incorporated battery configuration achieves a commendable combination of capacity, rate, and cycle stability (1491 mA h g–1 at 0.2 C, 754 mA h g–1 at 5 C, and initial capacity of 1069 mA h g–1 with an ultralow decay rate of 0.040% per cycle over 1000 cycles at 1 C) along with remarkably mitigated anode corrosion and low self-discharge.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c13193.TG plot for the Super-P/sulfur composite, SEM images of CNTs, XPS survey spectra of WS2/CNTs before and after Li2S6 adsorption, optimized WS2 (001) surface model and Li2S6 molecular structure, SEM images of PP and WS2/CNTs separators and digital images of the WS2/CNTs separator under bending/folding and after cycling, SEM image coupled with EDX mappings and TEM image of WS2/CNTs after cycling, polysulfide penetration test of PP, CNT, and WS2/CNTs separators, equivalent circuit models and EIS simulation results, CV and GCD profiles of four different battery configurations, and GCD profiles of the battery using WS2/CNTs as a cathode additive and separator coating at different scan rates, and electrochemical performance comparison of Li–S batteries based on different functional separators or cathode additives (PDF)This article has not yet been cited by other publications.

Perovskite Lithium Lanthanum Titanate-Modified Separator as Both Adsorbent and Converter of Soluble Polysulfides toward High-Performance Li-S Battery

Effective Dual Polysulfide Rejection by a Tannic Acid/Fe-III Complex-Coated Separator in Lithium-Sulfur Batteries

Three-Dimensional Ordered Fevo4 Nanocatalyst-Modified Separator Enables Suppressed Polysulfides Shuttling and Boosted Redox Conversion in Li-S Batteries

Suppression Of Polysulfide Shuttling With A Separator Modified Using Spontaneously Polarized Bismuth Ferrite For High Performance Lithium-Sulfur Batteries

A Novel Laminated Separator with Multi Functions for High-Rate Dischargeable Lithium–sulfur Batteries

A Separator with Double Coatings of Li4Ti5O12 and Conductive Carbon for Li‐S Battery of Good Electrochemical Performance

A Separator with Double Coatings of Li<sub>4</sub>Ti<sub>5</sub>O<sub>12</sub> and Conductive Carbon for Li-S Battery of Good Electrochemical Performance

A Separator with Double Coatings of Li 4 Ti 5 O 12 and Conductive Carbon for Li-S Battery of Good Electrochemical Performance.

A Trifunctional Separator Based on a Blockage-Adsorption-Catalysis Synergistic Effect for Li-S Batteries

Empowering polypropylene separator with enhanced polysulfide adsorption and reutilization ability for high-performance Li-S batteries

Novel Bifunctional Separator with a Self-Assembled FeOOH/Coated g-C 3 N 4 /KB Bilayer in Lithium–Sulfur Batteries

Ultra-thin nanosheets decorated in-situ S-doped 3D interconnected carbon network as interlayer modified Li-S batteries separator for accelerating adsorption-catalytic synergistic process of LiPSs

A Sustainable Multipurpose Separator Directed Against the Shuttle Effect of Polysulfides for High‐Performance Lithium–Sulfur Batteries

High-Performance Cross-Linked Particle-Like LaNiO 3 As a Multifunctional Separator to Significantly Enhance the Redox Kinetics of Lithium–Sulfur Batteries

Separator engineering toward suppressed shuttle effect and homogenized lithium deposition in lithium−sulfur batteries

Titanium-Containing Metal–Organic Framework Modified Separator for Advanced Lithium–Sulfur Batteries

3D Tungsten Disulfide/Carbon Nanotube Networks as Separator Coatings and Cathode Additives for Stable and Fast Lithium–Sulfur Batteries

Towards High-performance Lithium-Sulfur Batteries: the Modification of Polypropylene Separator by 3D Porous Carbon Structure Embedded with Fe3C/Fe Nanoparticles

Separator Modified by Cobalt‐Embedded Carbon Nanosheets Enabling Chemisorption and Catalytic Effects of Polysulfides for High‐Energy‐Density Lithium‐Sulfur Batteries

A dual-coated multifunctional separator for the high-performance lithium-sulfur batteries

TiO2@Porous carbon nanotubes modified separator as polysulfide barrier for lithium-sulfur batteries