Abstract:The “shuttle effect” and slow conversion kinetics of lithium polysulfide severely hinder the practical application of lithium–sulfur (Li–S) batteries. A perovskite functional separator (LaNiO3@PP) was introduced into lithium–sulfur batteries for applications; the lanthanum and nickel elements on the A-site and B-site have been proved to have good adsorption and catalytic effects on LiPSs in previous studies, and constructing the material with such dual active sites can greatly enhance its adsorption capacity for LiPSs. LaNiO3 prepared by the sol–gel method has the characteristics of low raw material cost and a simple synthesis method, which is an important prerequisite for product commercialization. It is found that the impedance of LaNiO3@PP batteries is low, which is favorable for the kinetic process of the batteries. According to the self-discharge experiment, it can be proved that LaNiO3@PP has a good ability to suppress self-discharge, and the capacity loss is only 8.76% after 7 days of resting, because LaNiO3 converts polysulfide to sulfate and the sulfate intermediate to Li2S through further electrochemical reaction during the discharge process, which effectively suppresses the shuttle effect and reduces the loss of active material for LaNiO3@PP with significantly high specific capacity and rate capability as well as stable long-cycle performance. For an area loading of 1.106 mg cm–2, the initial specific capacity at 0.1C is 1320.28 mAh g–1, and the discharge specific capacity of 591.40 mAh g–1 can still be maintained after 300 long cycles at 0.5C. When the area loading reached 4.926 mg cm–2 and the electrolyte-to-activator ratio (E/S) was 8.1 μL mg–1, and the initial capacity at 0.2C was 665.49 mAh g–1, the good electrochemical performance was maintained after 50 cycles. This work provides a new strategy for the preparation of high performance and high stability Li–S battery separators

Well-Dispersed Ov-NiCo2O4 Nanospheres Modified Separator for Li-S Batteries

Three-Dimensional Ordered Fevo4 Nanocatalyst-Modified Separator Enables Suppressed Polysulfides Shuttling and Boosted Redox Conversion in Li-S Batteries

Two-dimensional Molybdenum Nitride Nanosheets Modified Celgard Separator with Multifunction for LiS Batteries

Multifunctional Ni/NiO heterostructure nanoparticles doped carbon nanorods modified separator for enhancing Li–S battery performance

Suppression Of Polysulfide Shuttling With A Separator Modified Using Spontaneously Polarized Bismuth Ferrite For High Performance Lithium-Sulfur Batteries

Accelerating catalytic conversion and chemisorption of polysulfides for advanced Li-S batteries from incorporating Fe0.64Ni0.36@Co5.47N hetero-nanocrystals into boron carbonitride nanotubes

A multifunctional separator modified with cobalt and nitrogen co-doped porous carbon nanofibers for Li–S batteries

Application of Ni-MOF Derived Ni-C Composite on Separator Modification for Li-S Batteries

High-Performance Cross-Linked Particle-Like LaNiO 3 As a Multifunctional Separator to Significantly Enhance the Redox Kinetics of Lithium–Sulfur Batteries

Polyaniline-Coated Cobalt–Iron Oxide Composites Modified Separator for High Performance Lithium–Sulfur Batteries

A Ni-MOF derived graphene oxide combined Ni<sub>3</sub>S<sub>2</sub>–Ni/C composite and its use in the separator coating for lithium sulfur batteries

A Ni-MOF derived graphene oxide combined Ni 3 S 2 -Ni/C composite and its use in the separator coating for lithium sulfur batteries.

Three-in-one LaNiO 3 functionalized separator boosting electrochemical stability and redox kinetics for high-performance Li-S battery

Empowering polypropylene separator with enhanced polysulfide adsorption and reutilization ability for high-performance Li-S batteries

Cobalt Nitride Nanoparticles Encapsulated in N‐Doped Carbon Nanotubes Modified Separator of Li–S Battery Achieving the Synergistic Effect of Restriction‐Adsorption‐Catalysis of Polysulfides

Ni/SiO2/Graphene-modified separator as a multifunctional polysulfide barrier for advanced lithium-sulfur batteries

Oxygen vacancy-rich MnO nanoflakes/N-doped carbon nanotubes modified separator enabling chemisorption and catalytic conversion of polysulfides for Li-S batteries

Nitrogen-doped sheet VO2 modified separator to enhanced long-cycle performance lithium-sulfur battery

Bimetallic Ni–Co MOF@PAN modified electrospun separator enhances high-performance lithium–sulfur batteries

Constructing a Catalytic Reservoir Using Cobalt Nanoparticles-Mos2@nitrogen Doped Carbon Nanotubes on the Separator to Immobilize Polysulfides and Accelerate Their Conversion for Lithium-Sulfur Batteries

ZrO 2 nanoparticle modified hierarchically porous carbon nanofibers for multifunctional separator with prominent confinement and excellent catalysis of lithium polysulfide for Li-S cell