Abstract:Aiming at the magnetic seal in an aero-engine accessory, the range of magnetic force required for the normal operation of the magnetic seal is analyzed. The finite element analysis method based on the Maxwell stress tensor method is used to calculate the magnetic force between the dynamic ring and the magnetic static ring in the magnetic sealing system. The magnetic force under different magnetization modes and gaps is tested by the magnetic measuring test bench, which verifies the correctness of the magnetic calculation method. The effects of permanent magnet material, permanent magnet magnetization direction, magnetic seal structural parameters, and working conditions on the magnetic force between the dynamic ring/magnetic static ring in the magnetic seal are analyzed. Under the same structure, the magnetic force of NeFeB35, SmCo28, Alnico5, and Ferrite as magnetic static rings is compared. The results show that NdFeB35 has the largest magnetic force, SmCo28 is second, Alnico5 and Ferrite are relatively small, and their magnetic forces are about 1/4 to 1/5 of the first two materials. When the rotor or the casing is moving axially, NeFeB35 and SmCo28 materials with large magnetic force should be selected to meet the normal working requirements. Under the same material, the magnetic forces of axial, radial, and radiative magnetization modes are compared. the ratio of magnetic force under axial, radiative, and radial magnetization is about 2.3:1.1:1. If NeFeB35 and SmCo28 materials are axially magnetized, their magnetic forces will exceed the allowable range, which will increase the seal wear. The increase in the inner diameter of the dynamic ring and the gap between the dynamic ring and the magnetic static ring causes a decrease in the magnetic force. The increase in temperature affects the magnetic properties of permanent magnetic material, which leads to the decline of magnetic force between the dynamic ring and the magnetic static ring. The increase in rotor speed leads to the acceleration of the fluctuation frequency of the magnetic force. Still, the maximum and minimum values of the magnetic force under different speeds remain unchanged, and the maximum fluctuation rate is less than 3%. According to the analysis results, the fitting formula of magnetic force calculation is presented by the orthogonal test and the least squares method.

Determination of the shear force of high-coercive permanent magnets from an alloy of neodymium—iron—boron rare-earth elements of 5 mm thickness

Fe65B22Nd9Mo4 bulk nanocomposite permanent magnets produced by crystallizing amorphous precursors

Rotor Strength Analysis for High Speed Permanent Magnet Machines

Variation of Torque Transmitted Via a Standard Magnetic Coupling without Altering its Overall Dimensions by Changing the Grade and Dimensions of Permanent Magnets with a 7 mm Air Gap Between the Magnets

Performance of closed-form equations for force between cylindrical magnets over wide range of volume, aspect ratio, and force

Calculation of Field and Force of Halbach Arrays: Improved Magnetic Charge Method for Irregular Magnetized Magnets

TRANSMISSION TORQUE OF A STANDART MAGNETIC COUPLING DEPENDING ON THE PERMANENT MAGNET BRAND AND ITS SHAPE WITH GAP BETWEEN THE MAGNETS OF 5 MM

Torque Transmitted by a Standard Magnetic Coupling of Fixed Dimensions with Permanent Magnets of Different Types and Sizes

The dependence of coercivity on anisotropy field in sintered R-Fe-B permanent magnets

Strength Analysis for Surface-mounted Permanent Magnet Rotor in High-Speed Motor

Most frequently asked questions about the coercivity of Nd-Fe-B permanent magnets

Magnetic Forces Between Arrays of Cylindrical Permanent Magnets

Computational Design of the Rare-Earth Reduced Permanent Magnets

Accurate machine-learning predictions of coercivity in high-performance permanent magnets

Defect manipulation for the coercivity enhancement of Nd-Fe-B permanent magnets

Research on magnetic force of magnetic seal in aero-engine

Interplay between Exchange Interaction and Magnetic Shape Anisotropy of ferromagnetic nanoparticles in a non-magnetic matrix for rare-earth-free permanent magnets

A comparative study of Nd15Fe78B7 and Nd15Co78B7 systems: phase formations and coercivity mechanisms

First-principles study of permanent magnets

Investigation of magnetic properties of MnBi/Co and MnBi/Fe 65 Co 35 nanocomposite permanent magnets by micro-magnetic simulation

Magnetic Properties of Hard Magnetic Alloy Fe – 28% Cr – 13.4% Co – 2% Mo – 0.5% Si