Abstract:The paper investigated the effect of selected processing conditions during gear grinding on the value and distribution of microhardness and residual stress formed in the technological surface layer of gears after thermochemical treatment (TCT) conducted by a continuous single-piece flow method.The gears were carburised with LPC at 920C, then quenched in a 4D Quenching chamber at 7 bar and tempered at 190C for 3 hours. In the next step, the working surfaces of the gear teeth were ground by supplying grinding fluid (GF) to the grinding zone using the WET method and the MQL method with a minimum amount. Measurements were made on the distribution of microhardness and residual stress formed in the technological surface layer of gears after thermochemical treatment and after the grinding process.The results of the study showed the influence of workpiece speed vw and the method of delivery to the grinding zone GF on selected parameters describing the condition of the technological surface layer of the teeth of gears made of 20MnCr5 steel. The grinding process with a white aluminium oxide grinding wheel causes deterioration in the material's residual stress state. For each of the three analysed workpiece speeds vw, smaller changes in microhardness with respect to the microhardness of the material before grinding occur in the surface layer of samples ground with GF fed with the MQL method. Similarly, residual stress values are in the area of favourable compressive stresses.Environmental considerations and the need to comply with increasingly stringent environmental protection and worker safety regulations are pushing researchers and entrepreneurs to completely eliminate or reduce the consumption of grinding fluids in the grinding process. Based on the research and analysis carried out in this study, it was concluded that applying minimum GF by the MQL method could be an alternative to the conventional WET method.In sustainable manufacturing, it is extremely important to produce high-quality items while reducing the cost of manufacturing and taking care of the environment and workers' health. This includes the manufacture of gears, a basic component used in gear transmissions in the automotive industry, for example. The research has established that it is possible to use the MQL method, which reduces the amount of GF used when grinding the working surfaces of gear teeth, as an alternative to the conventional WET method.The conducted research was the first to determine the most favourable conditions, in terms of the obtained residual stresses and microhardness, for grinding the working surface of gear teeth using the MQL method.

Shear cutting induced residual stresses in involute gears and resulting tooth root bending strength of a fineblanked gear

Analytical Solution to Bending and Contact Strength of Spiral Bevel Gears in Consideration of Friction

Influences of tooth flank finishing after fine particle shot peening on tooth surface texture and fatigue life of vacuum carbonitrided gears

Bending fatigue life oriented tooth flank dry-grinding tool modification for cleaner manufacturing of spiral bevel gear product

Investigations on the tooth root bending strength and the fatigue fracture characteristics of case-carburized and shot-peened gears of different sizes

Gear Root Bending Strength: A Comparison Between Single Tooth Bending Fatigue Tests and Meshing Gears

Material Influence on the Micropitting and Wear Resistance of Nitrided External and Internal Gears

Development of a free-form tooth flank optimization method to improve pitting resistance of spur gears

Inclusion-Based Model: Calculating Tooth Root Bending Strength Considering Steel Cleanliness

Prediction of residual stress depth profiles in case-carburized gears

Simulation study of the punching forming process and die wear of spur gears

Modeling and Analysis of Deformation for Spiral Bevel Gear in Die Quenching Based on the Hardenability Variation

Gear Tooth-Forming Mechanism and Experimental Research of a Spiral Bevel Gear Rolling Process Using Local Induction Heating

Analysis on wear patterns and mechanisms of carbide tool for face-hobbing of spiral bevel gear

Optimized Compound Layer Design for Highly Loaded Nitrided Gears

Flank fractures on spiral bevel gears—transfer of analytical methods for the estimation of residual stresses from cylindrical gears to bevel gears

Ultrasonic rolling strengthening effect on the bending fatigue behavior of 12Cr2Ni4A steel gears

Effect of tooth root fillet on root bending stress

Effect of grinding conditions of gears made of 20MnCr5 steel after single-piece flow heat treatment on the condition of the surface layer of the tooth working surface

Finite Element Analyses of Non-Standard Spur Gears

NUMERICAL SIMULATION AND EXPERIMENTATION CUP-SHAPED THIN-WALLED INNER RECTANGULAR GEAR FORMED BY SPINNING