Abstract:Journal of Fire Sciences, Ahead of Print. The fire growth rate of interior linings, furnishings, and construction materials is measured in full-scale fire tests such as the ASTM E84 Steiner Tunnel, the ISO 9705 room fire, and a passenger aircraft fuselage as the flame-spread rate, time-to-flashover, or time to incapacitation, respectively. The results are used to indicate the level of passive fire protection afforded by the combustible material or product in the test without providing any insight into the burning process. These large-scale tests require many square meters of product, are very expensive to conduct, and can exhibit poor repeatability–making them unsuitable for product development, quality control, product surveillance, or regulatory compliance. For this reason, smaller (0.01 m2) samples are tested in bench-scale fire calorimeters under controlled conditions, and these one-dimensional burning histories are correlated with the results of the two- and three-dimensional burning histories in full-scale fire tests by a variety of empirical and semi-empirical fire propagation indices, as well as analytic and computer models specific to the full-scale fire test. The approach described here defines the potential of a material to grow a fire in terms of cone calorimeter data obtained under standard conditions. The fire growth potential, λ (m2/J), is the coupled process of surface flame spread and in-depth burning that is defined as the product of ignitability (1/Eign) and combustibility (ΔQ/ΔE) obtained from a combustion energy diagram measured in a cone calorimeter at an external radiant energy flux [math] (W/m2) above the critical flux for burning, [math]. However, the potential for fire growth, λ≡ (1/Eign)(ΔQ/ΔE) is only realized as a hazard when the heat of combustion of the product per unit surface area, Hc (J/m2), is sufficient to grow the fire. The dimensionless fire hazard of a combustible product of thickness b is therefore, Π = λHc, while the fire hazard of the component materials is an average over the product thickness, π = Π/b. The measurement of λ, Π, and π from combustion energy diagrams of heat release Q (J/m2) versus incident energy E (J/m2) is described, as well as a physical basis for a fire growth potential that provides simple analytic forms for λ in terms of the parameters reported in cone calorimeter tests. Experimental data from the literature show that rapid fire growth in full-scale fire tests of combustible materials occurs above a value of Π determined by the severity of the fire test.

Study on Combustion Characteristics of Ceiling Materials Using Cone Calorimeter

Flame behavior and fire-induced flow field characteristic in building corridor fire with longitudinal partition

Flammability Assessment Of Glubam With Cone-Calorimeter Tests

Investigation on the burning behaviors of the combustible ceiling with the impingement of an incipient fire source

An Experimental Study on the Combustion Characteristics of Major Combustible Materials in Office Buildings

Thermodynamic and Kinetic Characteristics of Combustion of Discrete Polymethyl Methacrylate Plates with Different Spacings in Concave Building Facades

Experimental Study on Burning Behaviors of Photovoltaic Panels with Different Coverings Using a Cone Calorimeter

Experimental Study on Behavior of Sidewall Fires at Varying Height in a Corridor-Like Structure

Effect of ceiling height on flame spread over horizontal poly(methyl methacrylate) slabs in corridor

A Study on the Quantitative Fire Performance Evaluation Method of Building Finishing Materials with a Focus on Medical Facilities

Correlation analysis of cone calorimetry test data assessment of the procedure with tests of different polymers

Correlation analysis of cone calorimetry and microscale combustion calorimetry experiments

Experimental and simulation study on the combustion fire spreading characteristics of aluminum composite panels with different thicknesses

Full-scale Experimental and Numerical Study of Smoke Spread and Temperature Distribution in a Room-Corridor Structure Building

Investigation of enclosure fire dynamics with inclined ceilings

Measuring the fire growth potential of combustible solids using a cone calorimeter

A Numerical Model for Ceiling Flame Spread Beneath A Combustible Board with Charring Material

Fire safety study of a perlite concrete chimney and wooden ceilings used in buildings based on experimental tests and CFD analysis

Evaluation of exterior wall cavity fires using an intermediate scale test method

A simplified calculation method on maximum smoke temperature under the ceiling in subway station fires

Analyzing Temperature Distribution Patterns on the Facing and Backside Surface: Investigating Combustion Performance of Flame-Retardant Particle Boards Using Aluminum Hypophosphite, Intumescent, and Magnesium Hydroxide Flame Retardants