Abstract:Fiber-reinforced plastic composites are sensitive to holes, as they cut the main load-carrying member in the composite (fibers) and they induce out-of-plane stresses. In this study, we demonstrated notch sensitivity enhancement in a hybrid carbon/epoxy (CFRP) composite with a Kevlar core sandwich compared to monotonic CFRP and Kevlar composites. Open-hole tensile samples were cut using waterjet cutting at different width to diameter ratios and tested under tensile loading. We performed an open-hole tension (OHT) test to characterize the notch sensitivity of the composites via the comparison of the open-hole tensile strength and strain as well as the damage propagation (as monitored via CT scan). The results showed that hybrid laminate has lower notch sensitivity than CFRP and KFRP laminates because the strength reduction rate with hole size was lower. Moreover, this laminate showed no reduction in the failure strain by increasing the hole size up to 12 mm. At w/d = 6, the lowest drop in strength showed by the hybrid laminate was 65.4%, followed by the CFRP and KFRP laminates with 63.5% and 56.1%, respectively. For the specific strength, the hybrid laminate showed a 7% and 9% higher value as compared with CFRP and KFRP laminates, respectively. The enhancement in notch sensitivity was due to its progressive damage mode, which was initiated via delamination at the Kevlar–carbon interface, followed by matrix cracking and fiber breakage in the core layers. Finally, matrix cracking and fiber breakage occurred in the CFRP face sheet layers. The specific strength (normalized strength and strain to density) and strain were larger for the hybrid than the CFRP and KFRP laminates due to the lower density of Kevlar fibers and the progressive damage modes which delayed the final failure of the hybrid composite.

Tensile and compressive damage assessment of a novel sandwich composite structure made of Kevlar/flax/epoxy hybrid laminates

Low-velocity Impact Damage Research on CFRPs with Kevlar-fiber Toughening

Enhanced damage tolerance and fracture toughness of lightweight carbon-Kevlar fiber hybrid laminate

Static behavior of thick flax/epoxy composite laminates: multi-instrumentation mechanical failure analysis

Flexural progressive damage and failure behavior of carbon-aramid/epoxy hybrid woven composites

Meso-Scale Damage Modeling of Hybrid 3D Woven Orthogonal Composites under Uni-Axial Compression

Compressive Experiment and Damage Simulation of A Composite Structure with Ply Drop-Off

A 3D finite element model to simulate progressive damage in unidirectional- and woven-fibre thermoplastic discontinuous-long-fibre composites

Empirical and numerical analysis of damage tolerance in multifunctional hybrid sandwich fiber reinforced polymers composite structures for aerospace applications using compression after impact (CAI) testing

Layer-wise damage prediction in carbon/Kevlar/S-glass/E-glass fibre reinforced epoxy hybrid composites under low-velocity impact loading using advanced 3D computed tomography

The influence of the inter-ply hybridisation on the mechanical performance of composite laminates: Experimental and numerical analysis

Experimental and numerical investigation of damage evolution in carbon fiber reinforced polymer stiffened panel in post-buckling regime

Post-Damage Compressive Strength of Woven Hybrid Composites Impacted with Various Energy Levels

Multi-scale analysis of the mechanical behaviour of a flax fibre reinforced composite under low-velocity impact

Enhanced Open-Hole Strength and Toughness of Sandwich Carbon-Kevlar Woven Composite Laminates

Low-velocity impact and quasi-static post-impact compression analysis of woven structural composites for automotive: Influence of fibre types and architectural structures

Hybridization effect of Kevlar and glass fiber on carbon/epoxy composites to enhance the damage strength under low velocity impact. Part II: Numerical simulations

Failure behavior and damage visualization of thick carbon/aramid hybrid woven composites under flexural loading conditions

Effects of Carbon/Kevlar Hybrid Ply and Intercalation Sequence on Mechanical Properties and Damage Resistance of Composite Laminates under Quasi-Static Indentation

Progressive Damage in Satin Weave Carbon/epoxy Composites under Quasi-Static Punch-Shear Loading

Face Damage Growth of Sandwich Composites under Compressive Loading: Experiments, Analytical and Finite Element Modeling