Abstract:Polymer electrolyte fuel cells (PEFCs) are electrochemical energy converters with high efficiency and zero pollutant emissions. The unassisted cold-start of PEFCs at -30 °C is one of the major challenges for automotive applications due to the freezing of supercooled water generated by the cathodic oxygen reduction reaction (ORR). Once triggered by the nucleus in cathode gas diffusion layers (GDLs), ice propagates through the active area, leading to oxidant gas blockage and cold-start failure 1 . The cold-start capability of PEFCs can be improved by preventing ice propagation, especially in GDLs. In our previous work 2,3 , after the GDLs were segmented by polytetrafluoroethylene (PTFE) into two regions, the PEFC kept operating for another 30 minutes after the first freezing event in one region. Nevertheless, the PTFE barrier limited the active area as well as the heat and electric conductivity of PEFCs. In contrast, patterned GDLs allow water cluster separation without the abovementioned limitations. The improvement of water management and cell performance under technical operating conditions was demonstrated 4 . Yet, the cold-start capability with patterned GDL needs to be further investigated. This work studies the effect of patterned GDLs on the water-ice phase transition and cold-start capability of PEFCs. First, non-isothermal differential scanning calorimetry (DSC) measurements were conducted to determine the onset freezing temperature distribution of supercooled water in patterned GDLs, taking into account various properties such as coating load and pattern size. It was observed that independent freezing events occurred in patterned GDLs in all cycles, as several freezing/exothermic peaks can be seen in Figure 1b . In contrast, ice propagated immediately in untreated GDL, as only one freezing peak was observed in all cycles (Figure 1d). By computing the integral of the heat flux curve, we obtained the corresponding cumulative icing ratio over 60 cycles, as presented in Figures 1a and 1c. The effective prevention of ice propagation is only observed in patterned GDLs. Second, to assess the cold-start capability, statistical isothermal cold-start measurements were conducted using a 4.4 cm 2 differential cell, with the cell temperature held at -7.5 °C, -10 °C, -15 °C, and 20 °C. In summary, nonconcurrent freezing events in patterned GDLs indicate that the use of patterned GDLs significantly improved the cold-start capability of PEFCs under isothermal subfreezing conditions. The findings of this work enhance the understanding of the cold-start dependence on the GDL and contribute to the development of unassisted freeze-start technology for PEFCs and the expansion of PEFCs applications. Figure 1

Improvement of cold start performance of polymer electrolyte fuel cell using microporous and gas diffusion layers with patterned wettability

Effect of Dual Porous Layers with Patterned Wettability on Low-Temperature Start Performance of Polymer Electrolyte Membrane Fuel Cell

Investigation of the effect of a hydrophilic layer in the gas diffusion layer of a polymer electrolyte membrane fuel cell on the cell performance and cold start behaviour

Performance Enhancement of Polymer Electrolyte Membrane Fuel Cells with a Hybrid Wettability Gas Diffusion Layer

Towards Improved Cold-Start Capability of PEFCs: Patterned Gas Diffusion Layers

Cold start optimization of the proton-exchange membrane fuel cell by penetrating holes in the cathode micro-diffusion layer

Effect of the Gas Diffusion Layer Design on the Water Management and Cell Performance of a PEM Fuel Cell

Effects of Cathode Gas Diffusion Layer Configuration on the Performance of Open Cathode Air-Cooled Polymer Electrolyte Membrane Fuel Cell

Two-Stage Microporous Layers with Gradient Pore Size Structure for Improving the Performance of Proton Exchange Membrane Fuel Cells

A design of gas diffusion media for polymer electrolyte membrane fuel cell: Characterization and water management investigation

Optimal Design of Cathode Gas Diffusion Layer with Arrayed Grooves for Performance Enhancement of a PEM Fuel Cell

Water Management Characteristics of Electrospun Micro-Porous Layer in PEMFC under Normal Temperature and Cold Start Conditions

Effects of porous properties on cold-start behavior of polymer electrolyte fuel cells from sub-zero to normal operating temperatures

One-step to prepare high-performance gas diffusion layer (GDL) with three different functional layers for proton exchange membrane fuel cells (PEMFCs)

Electrospun gas diffusion layers with reverse gradient pore structures for proton exchange membrane fuel cells under low humidity

Optimization of microporous layer perforation design for enhanced liquid water management in PEM fuel cells

Developing Next Generation High Performance Polymer Electrolyte Membrane Fuel Cells Using Metal Foam As Gas Diffusion Layer

Gradient Hydrophobic Microporous Layer for High-Performance Proton-Exchange Membrane Fuel Cells

Effect of Cathode Gas Diffusion Layer on Water Transport and Cell Performance in Direct Methanol Fuel Cells

Characterisation of Novel and High Performing Double-Sided Microporous-Layers-Coated Gas Diffusion Layers for Polymer Electrolyte Membrane Fuel Cells

A New Integrated GDL with Wavy Channel and Tunneled Rib for High Power Density PEMFC at Low Back Pressure and Wide Humidity