Abstract:The design of cathode catalyst layer (CL) is essential to improve the mass transfer capacity of proton exchange membrane (PEM) fuel cell and increase power density. In this work, cathode CL is divided into three sub-layers, and each sub-layer is added nano-particles with different wettability. The gradient CL with hydrophilic SiO2 particles at inner layer and hydrophobic polytetrafluoroethylene (PTFE) particles at outer layer significantly enhances the performance of membrane exchange assembly (MEA). Its performance is 895 mW/cm2@0.6 V, which is 24.1 %higher than CL without any particles (721 mW/cm2@ 0.6 V). Under operating conditions of high current density, high cathode humidity and high air stoichiometry, the gradient CL has only a little voltage loss. Through Electrochemical Impedance Spectroscopies (EIS) impedance analysis under high current density (1.8A/cm2), mass transfer resistance of gradient CL is 25.4 Ω, and is much smaller than the mass transfer resistance of the homogeneous CL of 35.1 Ω, which reflects the significant enhancement in mass transfer capacity of gradient CL. The gradient catalyst layer is suitable for a wider range of current density, humidity, and stoichiometry, but excessive cathode gas stoichiometry causes a decrease in performance, which is caused by excessive drainage capacity. In addition, 18 different gradient CLs are designed and manufactured, and the gradient CL with catalyst coated membrane (CCM) structure has the best performance. In gradient CL, increasing the capillary pressure difference between sublayers is the key to performance improvement. It is confirmed that the property of MEA with appropriate wettability gradient design can be significantly improved.

Gradient Hydrophobic Microporous Layer for High-Performance Proton-Exchange Membrane Fuel Cells

High-Performance Proton Exchange Membrane Fuel Cells Enabled by Highly Hydrophobic Hierarchical Microporous Carbon Layers Grafted with Silane

Silane-functionalized Carbon with Super-Hydrophobicity Advancing Microporous Layer for Proton Exchange Membrane Fuel Cells

Two-Stage Microporous Layers with Gradient Pore Size Structure for Improving the Performance of Proton Exchange Membrane Fuel Cells

Titanate-Grafted Carbon Black-Facilitated MPLs for Advanced Proton Exchange Membrane Fuel Cells

Superhydrophobic Carbon Functionalized by Chemical Grafting of Fluoroalkylsilane Enables an Efficient Microporous Layer for Proton-Exchange Membrane Fuel Cells

The buffer microporous layer improved water management for proton exchange membrane fuel cell at varying humidification

The microporous layer in proton exchange membrane fuel cells, from transport mechanism to structural design

Electrospun gas diffusion layers with reverse gradient pore structures for proton exchange membrane fuel cells under low humidity

Rational design of carbon network structure in microporous layer toward enhanced mass transport of proton exchange membrane fuel cell

Carbon-Nanowall Microporous Layers for Proton Exchange Membrane Fuel Cell

Durability improvement mechanism of proton exchange membrane fuel cell by microporous layer

Modulation of Transport at the Interface in the Microporous Layer for High Power Density Proton Exchange Membrane Fuel Cells

Optimization of microporous layer perforation design for enhanced liquid water management in PEM fuel cells

Coaly Graphite as an Eco-Friendly Material in the Microporous Layer of Proton Exchange Membrane Fuel Cells

Hydrophobicity enhancement of gas diffusion layer induced by hydrothermal deposition process and the electrochemical performance of proton exchange membrane fuel cell

Single-walled carbon nanotube interlayer modified gas diffusion layers to boost the cell performance of self-humidifying proton exchange membrane fuel cells

Performance Enhancement of Polymer Electrolyte Membrane Fuel Cells with a Hybrid Wettability Gas Diffusion Layer

Pore-Scale Modeling of Microporous Layer for Proton Exchange Membrane Fuel Cell: Effective Transport Properties

Design and optimization of gradient wettability pore structure of adaptive PEM fuel cell cathode catalyst layer

A novel hydrophilic‐modified gas diffusion layer for proton exchange membrane fuel cells operating in low humidification