Abstract:The results of studying the influence of mechanical alloying (MA) on the surface morphology, microstructure, and atomic–crystalline structure of particles of the Fe–Cr–Co–Ni–Mn multicomponent powder mixture are presented. The initial components are as follows: the R-10 radio-engineering carbonyl iron powder with average particle size d = 3.5 μm, the NPE-1 nickel powder with d = 150 μm, the PK-1u cobalt powder with d < 71 μm, the PKh-1M chromium powder with d < 125 μm, and the MR0 manganese powder with d < 400 μm. The MA of the prepared mixture was performed in an AGO-2 water-cooled mechanical activator using 9-mm steel balls with an acceleration of 90 g in air. The alloying time varies from 5 to 90 min. The ratio of the ball weight to the mixture weight is 20 : 1. X-ray diffraction patterns of the initial and alloyed mixtures, as well as of the sample formed by sintering, are recorded using a DRON 3M diffractometer in Fe K α radiation at 2θ = 30–100°. The microstructure of the mixture particles and the compact sample metallographic specimen after sintering are investigated by scanning electron microscopy. It is established that the peaks of initial components are absent in the X-ray diffraction pattern after mechanical activation for 90 min, and peaks corresponding to the phase representing the γ-Fe-based solid solution having a face-centered crystal lattice are presented. Herewith, the fraction of the amorphous phase increases to 20%. A compact single-phase material is formed from the mixture prepared after 90-min alloying by spark plasma sintering at 800°C for 10 min. Its density is 7.49 kg/cm 3 , resistivity is 0.94–0.96 × 10 –6 Ω m, and microhardness is 306–328 kg/mm 2 . The phase is uniformly distributed over the volume.

Increase of the mechanical response of pure aluminum by grain refinement retained with an alternative rapid sintering route

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Enhancement of FeCrAl-ODS steels through optimised SPS parameters and addition of novel nano-oxide formers

Effect of Abnormal Grain Refinement on Synchronous Strengthening Behavior of Fe50Mn30Co10Cr10 High Entropy Alloys

Indirect Induction Sintering of Metal Parts Produced through Material Extrusion Additive Manufacturing

Mechanically Blended Al: Simple but Effective Approach to Improving Mechanical Property and Thermal Stability of Selective Laser-Melted Inconel 718

Mechanical Alloying with the Partial Amorphization of the Fe–Cr–Co–Ni–Mn Multicomponent Powder Mixture and Its Spark Plasma Sintering to Produce a Compact High-Entropy Material

A review on mechanical alloying and spark plasma sintering of refractory high-entropy alloys: Challenges, microstructures, and mechanical behavior

Enhanced Sintering Kinetics in Aluminum Alloy Powder Consolidated Using Dc Electric Fields

Graded Microstructure and Mechanical Properties of Spark Plasma Sintered Fe-Cr alloys

Grain Refinement in A Alznmgcuti Alloy by Intensive Melt Shearing: A Multi-Step Nucleation Mechanism

Effect of interfacial Fe3O4 nanoparticles on the microstructure and mechanical properties of textured alumina densified by ultrafast high-temperature sintering

Optimization of process parameters for the development of Ni–Al-Ti-Mn-Co-Fe–Cr high entropy alloy system via spark plasma sintering

Improving strain hardening behavior in nano-intermetallic reinforced aluminum in-situ composites through an optimized twostep thermal processing method; sintering and uniaxial forging

Spark Plasma Sintering of Aluminum Nanocomposite Powders: Recent Strategy to Translate from Lab-Scale to Mass Production

Effect of Sintering Temperature on Phase Formation and Mechanical Properties of Al–Cu–Li Alloy Prepared from Secondary Aluminum Powders

Synthesis, characterization, and mechanical behavior of ultra-fine-grained Ti-6Al-5V alloy prepared by mechanical alloying and spark plasma sintering

Microstructures and Tensile Mechanical Properties of an Ultrafine Grained AA6063–5 Vol%sic Metal Matrix Nanocomposite Synthesized by Powder Metallurgy

Refining effect of an intermetallic inoculant on a Cu–Al–Mn shape memory alloy

Processing and Characterization of a Mechanically Alloyed and Hot Press Sintered High Entropy Alloy from the Al-Cr-Fe-Mn-Mo Family

Hierarchical Grain Refinement During the Laser Additive Manufacturing of Ti-6Al-4V Alloys by the Addition of Micron-Sized Refractory Particles