Abstract:Abstract After polymer flooding, a low-resistant dominant seepage channel forms at the bottom of the high-permeability reservoir, which is extremely disadvantageous for further enhanced oil recovery. In this study, we proposed a new method to plug the dominant seepage channel after polymer flooding, through fracturing–seepage–plugging using a solid-free plugging agent, which can achieve deeper and further regional plugging. This method involved dissolving the crosslinking agent and stabilizer in the water-based fracturing fluid (hereinafter referred to as the fracturing plugging agent) and transporting it to the target reservoir through hydraulic fractures. The fracturing plugging agent percolated into the deep part of the reservoir under the action of fracture closure pressure and gelled with the residual polymer in the formation to achieve deep regional plugging of the advantageous channel. To study the percolation law of fracturing plugging agent in the dominant channel, high-pressure displacement experiments were conducted using natural cores under different permeability and concentration conditions of the fracturing plugging agent. The results showed that the percolation rate of the fracturing plugging agent was almost linearly related to reservoir permeability. Due to the formation of micro-fractures and crosslinking reactions, the percolation rate first increased and then decreased to a stable state. After a certain period, the pores were blocked, resulting in a sharp decrease in the percolation rate and then decayed. In addition, the higher the concentration of fracturing plugging agent, the better the core plugging performance. Moreover, when the concentration of fracturing plugging agent injected into the core exceeded 3,000 mg/L, the core permeability increased, and the breakthrough pressure evidently increased three to four times. On the basis of this, rheometer tests, scanning electron microscopy (SEM) observations, and mercury intrusion tests were performed to evaluate gelation performance, shear effect, and pore retention morphology of the crosslinking system made by mixing the injected plugging agent and residual polymer in the reservoir. The results showed that the shear action could reduce the gelling property, and the concentration of fracturing plugging agent should be >3,000 mg/L to meet the requirements of gelling. Furthermore, the viscosity of the crosslinking system reached the peak value at approximately 72 h, forming a network space structure of layered superposition, thereby increasing viscosity by 40–50 times. Finally, SEM images revealed that after the fracture plugging agent was injected into the core, the micelles were mostly concentrated in the front and middle sections. The average pore radius of the core decreased by 8.620 μm, and the average porosity decreased by 54.85%.

The experimental investigation of the HPAM/phenolic resin deep profile system in fractured low-permeability reservoirs

Experimental Research on the Optimization and Evaluation of the Polymer/Chromium-Ion Deep Profile Control System for the Fractured Low-Permeability Reservoirs

Mechanism of Enhanced Oil Recovery for In-Depth Profile Control and Cyclic Waterflooding in Fractured Low-Permeability Reservoirs

Study on the Compatibility between Combined Control of Channel Plugging and Foam Flooding and Heterogeneous Reservoirs—Taking Bohai Z Oilfield as an Example

Experimental Study on the Optimization of Multi-level Nano-Microsphere Deep Profile Control in the Process of Gas Injection in Fracture-Type Buried-Hill Reservoirs

Simulation on the Water Controlling Performance of RPM in Hydraulic Fracturing of Low Permeability Reservoirs

Experimental Study on Phenol-Formaldehyde Resin Aggregates as In-Depth Conformance Control Agents Stabilized by Polymer

Performance of polyelectrolyte complex solution for water control in the hydraulic fracturing of low permeability reservoir

The Formation Mechanism of Residual Oil and Methods of Enhanced Oil Recovery in a Fractured Low-Permeability Metamorphic Rock Reservoir in Bohai Bay

A new method for plugging the dominant seepage channel after polymer flooding and its mechanism: Fracturing–seepage–plugging

Gelation and Plugging Performance of Low-Concentration Partially Hydrolyzed Polyacrylamide/Polyethyleneimine System at Moderate Temperature and in Fractured Low-Permeability Reservoir

A novel profile modification HPF-Co gel satisfied with fractured low permeability reservoirs in high temperature and high salinity

Compatibility evaluation of in-depth profile control agents in dominant channels of low-permeability reservoirs

An Experimental Research on Plate Models for Further Improving Oil Recovery after Polymer Flood

The Development and Field Application of Key Materials for Coupling Profile Control of Injection Well

Matching Method Between Nanoparticle Displacement Agent Size and Pore Throat in Low Permeability Reservoir

Experimental Performance Evaluation and Optimization of a Weak Gel Deep-Profile Control System for Sandstone Reservoirs

Field Application of Nanoscale Polymer Microspheres for In-Depth Profile Control in the Ultralow Permeability Oil Reservoir

Multi-Scale Visualization Study of Water and Polymer Microsphere Flooding through Horizontal Wells in Low-Permeability Oil Reservoir

Experimental study on the plugging and profile control of preformed particle gels in high temperature and salinity reservoir

Feasibility Study on the Microspheres for Deep Profile Control Technology in High Permeability of High Temperature and High Salinity Reservoirs