Abstract:Modular bridge expansion joints (MBEJs) are commonly used in bridges and are often subjected to fatigue damages, which necessitate fatigue monitoring of MBEJs to ensure the reliable operation of the bridges. In this paper, a stress wave based active sensing approach using piezoceramic transducers is developed to monitor the fatigue damage of MBEJ. A MBEJ involves mainly center beam, edge beam, support bar, support box, sliding bearing, sliding spring, elastomeric strip seal, full-penetration weld and reinforcing plate. In practice, for a MBEJ, the part that is most prone to fatigue damage is the full-penetration weld between the center beam and the support bar. In this paper, a specimen, which is the full-scale center-beam/support-bar (CB/SB) assembly, was designed and fabricated to facilitate the experimental study. The assembly mainly includes center beam, support bar, reinforcing plate, and full-penetration weld. The lead zirconate titanate (PZT) transducer bonded on the support bar was used as the actuator and the PZT transducer mounted on the center beam was as the sensor. Dial indicators were utilized to measure the vertical displacement of the center beam. Two series of tests, including static test, and fatigue test, were performed on the specimen in an alternating fashion. Based on the number of cyclic loading, the experiment was divided into six different stages: 0th cycle (the healthy state), 0.8 million cycles, 1.6 million cycles, 2.4 million cycles, 3.2 million cycles, and 4 million cycles. The signals received by the PZT sensor were analyzed with the help of wavelet packet analysis. In addition, the structure stiffness also was considered as a comparative approach in this paper. Experimental results show that during the fatigue test, the structure stiffness decreases with the number of cycle loading. However, the method can only obtain the fatigue damage impact on the entire structure, and cannot determine the fatigue damage degree of a certain weld. On the other hand, the proposed method can accurately monitor the fatigue damage degree of full-penetration welds. The research results show that the developed piezoceramic enabled active sensing approach can monitor and estimate the fatigue damage in MBEJ in real-time.

Monotonic and fatigue loading behavior of quasi-isotropic graphite/epoxy laminate embedded with piezoelectric sensor

Structural Integrity Assessment of Composites Plates with Embedded PZT Transducers for Structural Health Monitoring

Experimental and numerical investigation of the bonding conditions of piezoelectric sensors under high compressive strains on structures

Fatigue life assessment and damage evolution in Z-pinned laminates

Study of the Fatigue Behavior of the Unidirectional Zylon/epoxy Composite Used in Pulsed Magnets

Piezoresistive response of carbon nanotube and carbon fiber/epoxy composites under cyclic loading

Influence of graphene nanoplatelet concentration on the electrical, mechanical, and piezoresistive properties of glass fiber/epoxy composites

Electrospun Polyvinylidene Fluoride Piezoelectric Fiber Glass/Carbon Hybrid Self-Sensing Composites for Structural Health Monitoring

Fracture Toughness of Laminates Reinforced by Piezoelectric Z-Pins

Efficacy of PZT Sensors Network Different Configurations in Damage Detection of Fiber-Reinforced Concrete Prisms under Repeated Loading

Interfacial Effect on Quantitative Concrete Stress Monitoring Via Embedded PZT Sensors Based on EMI Technique

Effect of Lateral Pressure on the Non-Linear Behaviour of Pzt Ceramics

Experimental study and piezoresistive mechanism of electrostatic self-assembly of carbon nanotubes–carbon black/epoxy nanocomposites for structural health monitoring

Embedded Pt-PVDF sensor without compromising mechanical properties of GFRP for on-line sensing

Mechanical performance of carbon-epoxy laminates. Part II: quasi-static and fatigue tensile properties

Multifunctional composite material based on piezoelectric nanofibers and Cu-CFRP electrodes for sensing applications

High-performance strain sensors based on functionalized graphene nanoplates for damage monitoring

Health Monitoring for Composite Materials with High Linear and Sensitivity GnPs/epoxy Flexible Strain Sensors

Fatigue accumulated damage in notched quasi-isotropic composites under high-temperature conditions: A discussion on the influence of matrix nature on the stress energy release rate

Monitoring Fatigue Damage of Modular Bridge Expansion Joints Using Piezoceramic Transducers