Abstract:This thesis describes Near Infrared (NIR) initiated photopolymerization of multifunctional acrylic esters with NIR-LEDs emitting between 750 – 870 nm. These systems comprise a zwitterionic cyanine as sensitizer and an iodonium salt with distinct substitution pattern in both the cation and anion. An optically open window from the UV into the visible part allows embedding of functional materials covering particular this spectral range. Reactivity was studied with a synchronized photo-DSC comprising a self-designed hardware setup for data acquisition. 28 new iodonium salts ([A-I-B]+X-) were studied to show the influence of structural pattern on reactivity. [A-I-B]+X- possesses a different substitution pattern for the cation and the anion, respectively. Electron transfer of the excited state of the polymethine to the iodonium cation bearing different anions such as benzilate, lactate, NO3-, PF6-, SbF6-, p-CH2=CH-Ph-SO3-, p-C12H15-Ph-SO3-, CF3SO3-, C4F9SO3-, B(CN)4-, B(Ph)4-, B(PhF5)4-, N(CN)2- or (SO2-CF3)2N- results in initiating radicals. Although most of these anions do not participate in the redox mechanism, there exists a certain dependence between reactivity and the nature of the anion. Anions with low coordination behavior ((SO2-CF3)2N-, B(Ph)4-,B(PhF5)4-, B(CN)4-) result in acceptable reactivity. This may be explained by the conductivity of the salt in the acrylate monomers such as hexane-1,6-diol diacrylate, tripropylene glycol diacrylate, poly(ethylene glycol) diacrylate and trimethylolpropane triacrylate being different. A high ion mobility leads connects always to a high conductivity. Thus, complete dissociation is necessary to obtain a reactive system. The solubility of the different iodonium salts covers several g/L up to well mixable systems (>2000 g/L). A good solubility is not mandatory to obtain a high reactivity but it is desirable from a practical point of view. Particular the bis(trifluoromethylsulfonyl) imide anion (N(SO2-CF3)2-) results in giant solubilities depending on the iodonium cation. Such photoinitiating systems are interesting because they bleach at the excitation wavelength and open therefore the opportunity to cure coatings with large thickness; that is a length up to several millimeters (14 mm). In addition, NIR-exposure additionally results in formation of light-stable brownish photoproducts. This represents an interesting alternative compared to brownish pigments used in dental materials. These findings require to understand the mechanism of sensitizer decomposition in more detail applying exposure kinetics and a coupling of Ultra Performance Liquid Chromatography (UPLC) with mass spectrometry (MS) to analyze the photoproducts formed. Data show unexpected cleavage of the polymethine chain at typical positions in case of the oxidized species. These were formed as a result of electron transfer between the excited state of the photosensitizer and the iodonium salt. UPLC-MS experiments additionally indicated a certain sensitivity of the system upon adding of acids and radicals generated by thermal decomposition of AIBN. Thus, treatment of the photoinitiator composition (sensitizer and iodonium salt) with either radical or proton forming agents led almost to the same products no matter the system was either exposed with NIR light or not. Futhermore, photo-initiated crosslinking of multifunctional acrylic esters in polymeric binders was investigated based on digital imaging using the Computer-to-Plate (CtP) technology applying laser exposure in the NIR at 830 nm. Iodonium salts derived from several borates and those with the bis(trifluoromethylsulfonyl) imide anion resulted in lithographic materials with high sensitivity being comparable with those used in industrial systems. Finally, iodonium salts comprising the bis(trifluoromethylsulfonyl) imide anion exhibit a lower cytotoxicity compared to those with the tetraphenyl borate anion as determined by the MTT-test using CHO-9-cells.

Hybrid Free-Radical/Cationic Phase-Separated UV-Curable System: Impact of Photoinitiator Content and Monomer Fraction on Surface Morphologies and Gloss Appearance

Effect of Copolymer on the Wrinkle Structure Formation and Gloss of a Phase-Separated Ternary Free-Radical/Cationic Hybrid System for the Application of Self-Matting Coatings

An Analysis of Photopolymerization Kinetics and Stress Development in Multifunctional Acrylate Coatings

Simultaneous Measurement of Polymerization Kinetics and Stress Development in Radiation-Cured Coatings: A New Experimental Approach and Relationship between the Degree of Conversion and Stress

Visible-Light Initiated Free-Radical/Cationic Ring-Opening Hybrid Photopolymerization of Methacrylate/Epoxy: Polymerization Kinetics, Crosslinking Structure, and Dynamic Mechanical Properties.

Macromol. Chem. Phys. 8/2015

Photocurable Epoxy Acrylate Coatings Preparation by Dual Cationic and Radical Photocrosslinking

Study on the Polymer Morphology and Electro-Optical Performance of Acrylate/Epoxy Resin-Based Polymer-Stabilized Liquid Crystals Based on Stepwise Photopolymerization

Viscoelastic Study of Single Chain Cyclized Polymeric Nanoparticles and Linear Polymers Blends

Influence of Photoinitiator Type and Curing Conditions on the Photocuring of Soft Polymer Network

Initiation of Surface Wrinkling During Photopolymerization

Kinetics of Photopolymerization for the Acrylate/Liquid Crystal Mixture

Study on the Photo-Curing Kinetics of Free Radical-Cationic Hybrid System Epoxy Acrylate Resin

Thiol–epoxy/thiol–acrylate Hybrid Materials Synthesized by Photopolymerization

Study on Free-Radical Resins Used in Stereolithography

Untersuchungen zur NIR-sensibilisierten radikalischen Photopolymerisation in multifunktionellen Monomeren

PHOTOPOLYMERIZATION KINETICS AND PHOTO-RHEOLOGICAL BEHAVIORS OF VINYL-MONOMERS

Novel Multifunctional Epoxy (Meth)acrylate Resins and Coatings Preparation via Cationic and Free-Radical Photopolymerization

Evolution of Material Properties During Free Radical Photopolymerization

A study of the photoactivities and thermomechanical properties of epoxy resins using novel [cyclopentadien-Fe-arene]+PF6− photoinitiators

Development of Methacrylate/Silorane Hybrid Monomer System: Relationship Between Photopolymerization Behavior and Dynamic Mechanical Properties