Abstract:OBJECTIVE:To employ a laser triangulation method for measuring the dynamic shrinkage of composite resins during polymerization, and to investigate the maximum shrinkage rate (S(max)) and the time at maximum shrinkage rate (t(max)).METHODS:A novel experimental set-up based on laser triangulation was utilized which was capable of real-time shrinkage strain measurements. Uncured composite was condensed into a PTFE mould and irradiated for 40 s. The laser signals obtained from lateral composite surfaces were monitored using a laser triangulation measuring system and were converted into the displacement of the tested surface. The volumetric shrinkage derived from the linear shrinkage was calculated by multiplying 3. Total volumetric shrinkage (%S) of the five restorative materials (AP-X, Charmfill, Charisma, Durafill VS, and Herculite Precis) was measured using three methods (laser triangulation method, Acuvol, and buoyancy method). S(max) and t(max) were measured using the laser triangulation method. Statistical analyses were done using the two-way ANOVA (P<0.05) and post hoc test.RESULTS:The highest shrinkage value was measured by Acuvol, followed by laser method, and the lowest was by buoyancy method. All the three methods of measuring %S generated the same, statistically secured ranking for the five light-cured restorative materials: DurafillVS < AP-X < Herculite Precis < Charisma < Charmfill. %S measured by laser triangulation method varied between 2.06% and 3.37%. S(max) varied between 4.39 μm/s and 29.25 μm/s. t(max) varied between 0.77 s and 1.59 s. Significant differences in S(max) (F=734.87,P<0.01) and t(max) (F=53.24,P< 0.01) for five composite resins were found.CONCLUSION:Laser triangulation method offers several advantages over the conventional methods of measuring polymerization shrinkage. It is simple, compact, non-invasive and suitable for measuring the dynamic polymerization shrinkage in real time without delay. Therefore, it can be used to characterize the shrinkage kinetics in a wide range of visible-light-cure materials.

Effect of Monomer Structure on Real‐Time UV‐Curing Shrinkage Studied by a Laser Scanning Approach

Polymerization Shrinkage of (meth)acrylate Determined by Reflective Laser Beam Scanning

Volume Shrinkage of UV-curable Coating Formulation Investigated by Real-Time Laser Reflection Method

Simultaneous Measurement of Polymerization Kinetics and Stress Development in Radiation-Cured Coatings: A New Experimental Approach and Relationship between the Degree of Conversion and Stress

An Analysis of Photopolymerization Kinetics and Stress Development in Multifunctional Acrylate Coatings

Exploration for Decreasing the Volume Shrinkage for Photopolymerization

UV Curing Behavior of Methacrylated Hyperbranched Poly(amine-Ester)s

Volume Shrinkage and Conversion Rate of Al2O3 Ceramic Stereolithography Suspension Polymerised by Ultraviolet Light

Monomer elution and shrinkage stress analysis of addition-fragmentation chain-transfer-modified resin composites in relation to the curing protocol

Effect of 2,2‐dimethyl Malonate on the Volume Shrinkage Control of the CaCO3/unsaturated Polyester Resin Composites

STUDY ON THE UV-CURING OF A NEW ALICYCLIC EPOXY ACRYLATE RESIN

Effect of Low-Shrinkage Monomers on the Physicochemical Properties of Experimental Composite Resin.

UV curable acrylate monomers: Structure ― activity relationship and selection criterion

[A New Dynamic Approach to Monitoring Dental Composite Curing Kinetics].

Polymerization Shrinkage Kinetics and Degree of Conversion of Resin Composites.

Effects of Compaction and UV Exposure on Performance of Acrylate/glass‐fiber Composites Cured Layer by Layer

Influence of reactive diluent on UV-curing of acrylate terminated hyperbranched polymers

Relationship between the adhesion properties of UV-curable alumina suspensions and the functionalities and structures of UV-curable acrylate monomers for DLP-based ceramic stereolithography

Mitigating Shrinkage Stress in UV-Curable Resin: Shape Memory Microcapsules Enable Shrinkage Stress Reduction via Photopolymerization-Induced Shape Recovery

Shrinkage Effects in Photopolymerizable Resin containing Polymer Filler for SL

Enhancing adhesive strength and durability: Exploring the benefits of upconversion particle-assisted near-infrared photopolymerization