Abstract:Zircaloy-4 is used as a fuel cladding material for water reactors, as it has good mechanical properties, corrosion resistance, and a low thermal neutron absorption cross section. However, the mechanical performance of Zircaloy-4 can be reduced during service due to hydrogen uptake and hydride formation. These hydrides are brittle, and often reduce the strength and toughness of materials as well as increase susceptibility to delayed hydride cracking (DHC). In this work, large grain Zircaloy-4 with hydrides was prepared and then cross sectioned using cryo-ion beam polishing, using plasma focused ion beam (pFIB) and broad ion beam (BIB) approaches to enable the preparation of a very high quality flat surface with no preferential etching of either the hydride or zirconium metal (typically metallographic polishing preferentially removes hydrides). Conventional and high angular resolution electron backscatter diffraction (EBSD) analysis were then used to explore morphology, deformation fields, and orientation relationships between the zirconium matrix and hydrides. Four maps were collected for analysis which included hydrides near grain boundaries: (a) where the hydride smoothly decorates across two of the connecting boundaries near a triple junction; (b) where the hydride smoothly decorates the boundary; (c) a mixture of smooth decoration of the interface and protrusion into the grains; (d) fine scale hydride that protrudes into one grain. This work highlights that incompatibility of the hydride within the zirconium matrix is strongly linked to the orientation relationship of the hydride and matrix, and the grain boundary character. These results may enable enhanced understanding of the role of hydrides in fracture as well as stress-induced hydride reorientation and DHC susceptibility.

Effect of hydrogen contents on the mechanical properties of Zircaloy-4

Hydride-Induced Responses in the Mechanical Behavior of Zircaloy-4 Sheets

Revealing the role of hydrogen content on the mechanical behavior and cracking mechanisms of Zircaloy-4 under strain

Temperature-dependent axial mechanical properties of Zircaloy-4 with various hydrogen amounts and hydride orientations

In-situ EBSD analysis of hydride phase transformation and its effect on micromechanical behavior in Zircaloy-4 under uniaxial tensile loading

Microstructure and mechanical properties evolution of hydrogenated Zircaloy-4 tube during thermal decomposition process of precipitated δ-hydride

Influence of temperature and hydrogen content on the transverse mechanical properties of Zircaloy-4 fuel cladding

Modeling and tests on the damage and fracture behaviors of non-irradiated zirconium alloys with different hydrogen concentrations at RT and 350°C

Hydride growth mechanism in zircaloy-4: Investigation of the partitioning of alloying elements

High-throughput Computing for Hydrogen Transport Properties in Ε-Zrh2

Effects of heat treatment on hydriding/dehydriding characteristics of Ti18Cr24V55Zr3 alloy

Characterization of local deformation around hydrides in Zircaloy-4 using conventional and high angular resolution electron backscatter diffraction

The effect of pressure on hydrogen solubility in Zircaloy-4

The role of hydrogen in zirconium alloy corrosion

Assessing the fracture toughness of Zircaloy-4 fuel rod cladding tubes: impact of delayed hydride cracking

The effect of δ-hydride on the micromechanical deformation of Zircaloy-4 studied by in situ high angular resolution electron backscatter diffraction

Study of Oxidation Behavior and Associated Microstructure Evolution of Zircaloy-4 Exposed to High Temperature Pure Steam

Effect of Zr Content on the Microstructures and Hydrogen Storage Properties of (Ti-Cr)_(45-x)V_(55)Zr_x(x=1～7) Alloys

Effect of hydride orientation on tensile properties and crack formation in zirconium alloy cladding tubes

Effects of Pre-Crack Depth and Hydrogen Absorption on the Failure Strain of Zircaloy-4 Cladding Tubes Under Biaxial Strain Conditions

Hydride precipitation dependence on α-parent orientation and plastic deformation in zirconium alloys