Abstract:Grinding executed in a lapping configuration is an alternative finishing process benefiting from both grinding and free-abrasive machining, while minimizing the heat effect impact. Electroplated tools can be effectively used in different abrasive processes, including high-speed grinding, however, the assessment of machining performance over time is a key factor in their correct use to achieve satisfactory technological results. In conventional grinding, bigger grain-coverage provides better results due to the higher bonding strength of grains. In lap-grinding, fracturing and crushing of the abrasive particles initially covered by the plating result in a suspension which is typically dosed continuously in free-abrasive machining. Due to this, the process transforms from two-body (grinding) to three-body abrasion (free abrasive machining) which may result in reduced grinding performance approaching asymptotically a specific value while improving surface finish. The main aim of the presented study is the evaluation of electroplated CBN tools used in lap-grinding of 40H alloy steel workpieces whose hardness was 54 HRC. The obtained results and observations of the working surface of CBN wheels and workpieces allowed for the identification of the wear characteristics for three nickel plating thicknesses corresponding to 35%, 50% and 65% of the nominal CBN crystal size and for specific process parameters. The surface roughness Ra parameter decreased gradually from the initial value 1.9 μm to the values below 0.7 μm for bigger B107 grains and for all plating thicknesses. For smaller B64 grains, the surface roughness and waviness parameters reached similar values to those obtained for the larger B107 grains at corresponding processing times. The lowest value of Ra parameter below 0.4 μm was obtained for B64 grains and for the thinnest plating but with a 50% reduction in material removal comparing to B107 grains. The Preston equation was employed to calculate the material removal as a function of time under variable process conditions in the machining zone due to the tool wear. This attempt extended the range of the material removal modeling, despite the fact that the electroplated wheels were subject to wearing down resulting in the gradual reduction in the efficiency, as well as in the change of the working conditions in the workpiece-tool contact zone.

Process limits in high-performance peel grinding of hardened steel components with coarse CBN grinding wheels

High performance peel grinding of steel shafts using coarse electroplated CBN grinding wheels

The use of Preston equation to determine material removal during lap-grinding with electroplated CBN tools

Current Status of Peel Grinding Technology

Self-sharpening property of porous metal-bonded aggregated cBN wheels during the grinding of Ti–6Al–4V alloys

Grain erosion wear properties and grinding performance of porous aggregated cubic boron nitride abrasive wheels

Influence of Electroplated CBN Wheel Wear on Grinding Surface Morphology of Powder Metallurgy Superalloy FGH96

Modelling and Analysis of the Bonding Mechanism of CBN Grains for Electroplated Superabrasive Tools—part 1: Introduction and Application of a Novel Approach for Determining the Bonding Force and the Failure Modes

Adhesive wear mechanism under combined electric diamond grinding

New profiling approach with geometrically defined cutting edges for sintered metal bonded CBN grinding layers

Analysis of Grindability and Surface Integrity in Creep−Feed Grinding of High−Strength Steels

CBN grain wear and its effects on material removal during grinding of FGH96 powder metallurgy superalloy

Grinding the sharp tip in thin NiTi and stainless steel wires

Effects of open pores on grinding performance of porous metal-bonded aggregated cBN wheels during grinding Ti–6Al–4V alloys

Potentials of Vitrified and Elastic Bonded Fine Grinding Worms in Continuous Generating Gear Grinding

Manufacture and Grinding Performance of A Polyimide Resin-Bonded Cbn Wheel for Precision Grinding of Ferrous Materials

Experimental Study of Time-Dependent Performance in Superalloy High-Speed Grinding with Cbn Wheels

Comparative analysis of two CBN grinding wheels performance in nodular cast iron plunge grinding

Grains Dynamic Strength Determination and the Optimal Combination of Components of a Diamondiferous Layer of Grinding Wheels

Experimental investigation on the feasibility of high-efficiency and precision grinding of silicon carbide ceramics with monolayer brazed diamond wheel

On the tribology and grinding performance of graphene-modified porous composite-bonded CBN wheel