Abstract:Al-Zn-Mg-Cu alloy, as an important lightweight structural material in the aerospace field, has ushered in a broader application space and proposed higher performance requirements. This paper presents the experimental investigation of the effect of Zr content on the microstructure refinement and performance improvement of cast Al-5.8Zn-2.3Mg-1.7Cu alloy, aiming to optimize the additional amount of Zr, refine the alloy grains, and improve the microstructure uniformity and mechanical properties. The chemical component, phase, and microstructure were observed by inductively coupled plasma, X-ray diffraction, optical microscope and scanning electron microscope; the hardness and mechanical properties were measured by Brinell hardness tester and tensile testing machine. The addition of different contents of Zr into the alloy can form fine dispersed or primary coarse Al3Zr phase, which has a significant effect on the microstructure and mechanical properties of the alloy. The results indicate that the addition of 0.05 wt% Zr does not significantly improve the grain refinement and mechanical properties, but the Brinell hardness reaches the maximum. As the Zr content rises, the grain refinement effect becomes more obvious, while the mechanical properties first increase and then decrease. The addition amount reaches 0.20 wt%, the second dendrite arm spacing is the smallest, the ultimate tensile strength, yield strength and elongation at room temperature reach the maximum of 296.74 MPa, 249.41 MPa and 8.26%, respectively. When the amount of Zr added exceeds 0.20 wt%, the existence of coarse and brittle primary Al3Zr phase reduces the mechanical properties, and the fracture morphology changes from ductile to brittle intergranular fracture.

The existing forms of Zr in Mg-Zn-Zr magnesium alloys and its grain refinement mechanism

Investigation on the Atomic Mechanism for Grain Refinement of Magnesium Alloys by Mg-Zr Master Alloy

Research on Grain Refinement of Sc and Zr Addition in an Al-Mg-Zn Alloy from Experiments and First-Principles Calculations

Enhanced Grain Refining Effect of Mg–Zr Master Alloy on Magnesium Alloys via a Synergistic Strategy Involving Heterogeneous Nucleation and Solute-Driven Growth Restriction

Solidification of Mg–Zn–Zr Alloys: Grain Growth Restriction, Dendrite Coherency and Grain Size

Effect of Trace Zr on Microstructure and Hardness of Al-Zn-Mg-Cu Alloy Prepared under Supergravity

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Effect of Zr grain refinement on solidification behavior of Mg–3Nd alloy by cooling curve thermal analysis

Grain refinement of magnesium alloys by Mg-Zr master alloys: The role of alloy chemistry and Zr particle number density

Study on the grain refinement behavior of Mg-Zr master alloy and Zr containing compounds in Mg-10Gd-3Y magnesium alloy

Zr as an Alternative Grain Refiner in the Novel AlSi5Cu2Mg Alloy

Effects of Zr Addition on the Multi-Scale Second-Phase Particles and Fracture Behavior for Mg-3Gd-1Zn Alloy

Interaction Between Zr Addition and Intensive Melt Shearing on Grain Refinement of Commercial Purity Magnesium

Current Research Status of Grain Refinement Effect of Zr on Magnesium Alloy

Influence of Zr addition on the morphology of primary MgZn 2 in the solidification microstructure of Zn-6Al-3Mg alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Influence of Zr content on microstructure and mechanical properties of As-cast Al-Zn-Mg-Cu alloy

Effects of Zr on Microstructure and Properties of MgZn5Nd3.5 Alloy

Achieving Low-Temperature Zr Alloying for Microstructural Refinement of Sand-Cast Mg-Gd-Y Alloy by Employing Zirconium Tetrachloride

Effect of Zr addition on the microstructure evolution and mechanical properties of extruded Al-Cu-Li-Mn alloys

Grain Refining Mechanism in Mg–9Gd–4Y Alloys by Zirconium