Abstract:In the present work, the mechanical anisotropic behavior of low-carbon (Fe-0.07C) steel processed by asymmetric cold rolling was investigated. Three different types of dynamic recrystallization (DRX) mechanisms (continuous, discontinuous, and geometric) were observed in the microstructure of the 75 % cold-rolled sheet. The average intensity of γ-fiber was remarkably enhanced to 2.8 × R as rolling deformation increased to 50 % due to the formation of many deformation bands. After 75 % cold rolling, the average intensity of γ-fiber was significantly decreased to 1.4 × R due to the creation of new recrystallized grains. The results exhibited that the hardness of the low-carbon steel sheet was 260.1 HV by 75 % cold rolling, which was 1.75 times larger than the initial low-carbon steel sheet. With increasing deformation degree, the average yield and tensile strengths gradually improved and reached a peak value of 844.8 MPa and 881.7 MPa after 75 % cold rolling, respectively, which were 2.8 and 2.1 times that of the initial low-carbon steel sheet. By increasing the rolling reduction up to 50 %, the mechanical anisotropy gradually enhanced and by further increasing the cold deformation to 75 %, the anisotropy rapidly decreased due to the weakening of the γ-fiber texture. The strength was the highest along the transverse direction (90°) in all low-carbon steel sheets, and decreased at 0° and 45°. The dσ/dε-ε curves of the 50 % cold-rolled low-carbon steel sheet for the 45° and 90° tensile directions exhibited two distinct stages during the loading, however, that for the 0° revealed only one stage. A large number of parallel striations were present on the fracture surface of the 50 % deformed low-carbon steel sheet at 90° due to the presence of parallel deformation bands.

Characterization of Microstructure and Microtexture in a Cold-Rolled and Intercritically Annealed Dual-Phase Steel

On the Simultaneous Improving of Strength and Elongation in Dual Phase Steels via Cold Rolling

Effect of Warm Rolling Temperature on the Microstructure and Texture of Microcarbon Dual-Phase (DP) Steel

On the use of thermomechanical processing to enhance the strength-ductility-toughness balance of plain low-carbon steel

Medium-carbon dual-phase steels with spheroidized ferrite matrix

Study Of The Mechanical Behavior Of Dual-Phase Steel Based On Crystal Plasticity Modeling Considering Strain Partitioning

Effect of cold rolling reduction on microstructure, mechanical properties, and texture of deep drawing dual-phase (DP) steel

Microstructure and Mechanical Properties of Pure Copper Subjected to Skin Pass Asymmetric Rolling

Assessment of the Hardening Behavior and Tensile Properties of a Cold-Rolled Bainitic-Ferritic Steel

Microstructure tailoring for property improvements of DP steel via cyclic intercritical annealing

Asymmetric Rolling of Interstitial-Free Steel Using Differential Roll Diameters. Part I: Mechanical Properties and Deformation Textures

Annealing Temperature-Dependent Microstructure, Mechanical, and Tribological Properties of Intercritically Heat-Treated Dual-Phase Steel

Simultaneous enhancement of strength and ductility in ferrite-martensite steel via increasing the martensite fraction

Microstructure, Texture, and Deep Drawability under Two Different Cold-Rolling Processes in Ferritic Stainless Steel

Microstructures and Mechanical Properties of Dual Phase Steel Produced by Laboratory Simulated Strip Casting

Improved Mechanical Properties of Structural Steel via Developing Bimodal Grain Size Distribution and Intercritical Heat Treatment

Texture Distribution and Development through the Thickness of Grain Oriented Silicon Steel

Microstructure and Texture Evolution of Non-oriented Electrical Steel 50W600 during Processing

Mechanical anisotropic behavior of low-carbon steel processed by asymmetric rolling

Microstructures and Mechanical Properties of Commercial Purity Iron Processed by Asymmetric Rolling

TEXTURE DISTRIBUTION AND DEVELOPMENT THROUGH THE THICKNESS AFTER CROSS SHEAR ROLLING OF GRAIN ORIENTED SILICON STEEL