Abstract:In this work, a severe plastic deformation method, namely elliptical cross-section torsion extrusion (E-TE), was applied to achieve superplasticity of an in-situ TiB2/Al-Zn-Mg-Cu composite by obtaining the optimized microstructure of uniformly distributed particles and equiaxed-fine grains. The superplastic behavior and mechanisms of the E-TE processed composite were comprehensively investigated via tensile tests (at T = 350 degrees C-500 degrees C and epsilon = 10-1 s-1-10-3 s- 1) and microstructure characterizations. The tests demonstrated that the composite after a single pass of the E-TE gained a maximum elongation of 420% at 450 degrees C x 10-3 s-1. Even with the strain rate increasing to 10-2 s- 1, the elongation still reached 360%, which implies a high strain rate superplasticity. Analysis based on the strain rate sensitivity (m approximate to 0.20-0.35) and microstructure characterizations showed that the deformation and failure mechanisms of the composite vary with the temperature. When the temperature is within 350 degrees C-400 degrees C, the composite realizes deformation mainly through intragranular dislocation slip and fails by intragranular fracture. With the temperature of 425 degrees C-450 degrees C, the deformation is attributed to cooperative grain boundary sliding (CGBS) accommodated by dislocation activity and liquid phase, where a small fraction of liquid phases observed at the triple junctions of GBs facilitates the composite's superplasticity by reducing the stress concentration and deformation incompatibility. The failure is ascribed to the intergranular fracture by cavity formation/coalescence. For temperature within 475 degrees C-500 degrees C, numerous liquid phases formed at GBs and significantly weakened the GBs' strength, deteriorating the composite's superplasticity. The composite's failure is resulted from the intergranular fracture by strength weakening of GBs.

A physically based constitutive model of Ti-6Al-4 V and application in the SPF/DB process for a pyramid lattice sandwich panel

Quasi-static Compressive Behaviors of Large-Size Titanium Lattice Sandwich Structure Based on Pulse Hot-Wire Arc Additive Manufacturing

Superplastic Forming and Diffusion Bonding for Sandwich Structure of Ti-6al-4v Alloy

Constitutive modeling for the simulation of the superplastic forming of TA15 titanium alloy

The superplastic forming/diffusion bonding of TA7 titanium alloy for manufacturing hollow structure with stiffeners

Constitutive Modeling on the Ti-6Al-4V Alloy during Air Cooling and Application

The Structural Design and Superplastic Forming/diffusion Bonding of Ti2AlNb Based Alloy for Four-Layer Structure

Study of Macroscopic Defects of Four-Layer Structure of Ti–6Al–4V During Superplastic Forming/Diffusion Bonding

Process-structure-property Modeling for Postbuild Heat Treatment of Powder Bed Fusion Ti-6Al-4V

The superplastic forming/diffusion bonding and mechanical property of TA15 alloy for four‐layer hollow structure with squad grid

A Study of Titanium Alloy Integral Control Surface Based on Superplastic Forming/Diffusion Bonding

A Modified Constitutive Model With Grain Rotation for Superplastic Forming of Ti–6Al–4V Alloy

LBW/SPF/DB Combined Processing and Microstructure of TA15 Titanium Alloy Four-Layer Sandwich Structure with Square Grid

Mechanisms Behind the Superplastic Behavior of As-Extruded Tibw/Ti6al4v Composites with A Network Architecture

Superplastic Forming and Diffusion Bonding for Multilayer Structure of Ti-6Al-4V Alloy

Superplastic Behavior of an In-Situ TiB2 Particle Reinforced Aluminum Matrix Composite Processed by Elliptical Cross-Section Torsion Extrusion

Electrically assisted superplastic forming/diffusion bonding of the Ti2AlNb alloy sheet

Superplasticity in Ti–6Al–4V: Characterisation, modelling and applications

Numerical Simulation of Superplastic Forming and Diffusion Bonding of Ti Alloys

Thermo-mechanical modeling of lattice-core sandwich panels in powder bed fusion

Modeling of the Diffusion Bond for SPF/DB Titanium Hollow Structures