Abstract:Since the dawn of nanoscience, producing nanomaterials in a simple, low-cost, and high-yield manner has been a major issue. For the commercial manufacturing of nanomaterials, various bottom-up and top-down methodologies have been established. High-energy dry ball milling is widely used for the production of diverse nanomaterials, nanograins, nanoalloys, and nanocomposites. Physical grinding of inorganic solid waste into nanosize (1-100 nm) has improved their industrial applications particularly as water adsorbent. Application of nanosize spent oil shale by top-down methodology as adsorbent for phenol is addressed in the current research. The collected spent oil shale (SiO2 and Al2O3 making 45% of the material) has microstructure with average particle size of 56.6 μm. The dry grinding was performed in a vibrating ball mill at various grinding time (5-150 min) while keeping the grinding parameters constant including number of balls, ball size, total mass, vibration frequency, and amplitude. Upon grinding, the mean particle diameter of the bulk material was reduced to 191.8 and 85.2 nm using 0.5 and 0.1 mm grinding balls, respectively. The effect of grinding time on particle size and surface area was investigated; both particle size and surface area were not affected after 60 min of grinding. Physical grinding by 0.1 mm balls has notably improved surface area and total pore volume by 52% and 62%, respectively. Although nanosize particles (85.2 nm) perform better than bulk material for phenol uptake, they underwent serious aggregation at pH > 2 and ionic strength > 1.0 mM. Hence, the 191.8-nm size is selected to assess the effect of mechanical grinding on adsorption rate and equilibrium capacity for phenol as a common pollutant. Upon nanonization, adsorption rate of phenol was highly increased from 0.39 to 4.43 mg g-1 min-1 as analyzed by pseudo-second-order model. Adsorption isotherms were adequately presented by Sips model (prediction error 5.4-7.2%) with a maximum phenol retention capacity of 39.29 mg/g after nanonization compared to 10.71 mg/g for the raw material. The performance of the nanosize spent oil shale for phenol retention was promising when compared with advanced adsorbents like multiwalled carbon nanotube.

Sensitivity of oil shale particle surface to the applied load in ball mill

Impact of the grinding method on oil shale flotation

Microstructural Imaging and Characterization of Oil Shale Before and after Pyrolysis

Analysis Of Alumina Particles Size And Shape Formation From Developed Planetary Ball Mill

Impact of cationic-anionic surfactants on selective oil agglomeration of oil shale

Ultrafine dry grinding of talc by planetary mill: effects of operating conditions

Effect of grinded oil shale inclusion on some properties of concrete mixtures

Experimental Investigation of the Basic Characteristics and Wettability of Oil Shale Dust

Correlation of Size Reduction Rate of Inorganic Materials with Impact Energy of Balls in Planetary Ball Milling

Grinding kinetics of coal in wet ball-milling using the Taguchi method

Effect of grinding media on the milling efficiency of a ball mill

Characterization and utilization of solid residues generated upon oil and heat production from carbonate-rich oil shale

Effects of swelling-clay and surface roughness on the wettability of transitional shale

Effects of Ball Size on the Grinding Behavior of Talc Using a High-Energy Ball Mill

Evaluation of particle size reduction and agglomeration in dry grinding of natural quartz in a planetary ball mill

Factors affecting wear in tumbling mills: Influence of composition and microstructure

Dry Grinding Effect on Pyrophyllite-Quartz Natural Mixture and Its Influence on the Structural Alternation of Pyrophyllite.

Kinetics of Grain Size Reduction in Minerals Undergoing Ball Milling

Utilization of nanosize spent oil shale for water treatment: application of top-down nanonization technology for solid residues

Experimental Investigation of the Anisotropic Evolution of Tensile Strength of Oil Shale Under Real-Time High-Temperature Conditions

Differences in dry and wet grinding with a high solid concentration of coking coal using a laboratory conical ball mill: Breakage rate, morphological characterization, and induction time