Abstract:Ion beam-assisted deposition (IBAD) has been proposed as a promising texturing technology that uses the film epitaxy method to obtain biaxial texture on a non-textured metal or compound substrate. Magnesium oxide (MgO) is the most well explored texturing material. In order to obtain the optimal biaxial texture, the actual thickness of the IBAD-MgO film must be controlled within 12nm. Due to the bombardment of ion beams, IBAD-MgO has large lattice deformation, poor texture, and many defects in the films. In this work, the solution deposition planarization (SDP) method was used to deposit oxide amorphous Y2O3 films on the surface of Hastelloy C276 tapes instead of the electrochemical polishing, sputtering-Al2O3 and sputtering-Y2O3 in the commercialized buffer layer. An additional homogeneous epitaxy MgO (epi-MgO) layer, which was used to improve the biaxial texture in the IBAD-MgO layer, was deposited on the IBAD-MgO layer by electron-beam evaporation. The effects of growth temperature, film thickness, deposition rate, and oxygen pressure on the texture and morphology of the epi-MgO film were systematically studied. The best full width at half maximum (FWHM) values were 2.2° for the out-of-plane texture and 4.8° for the in-plane texture for epi-MgO films, respectively. Subsequently, the LaMnO3 cap layer and YBa2Cu3O7-x (YBCO) functional layer were deposited on the epi-MgO layer to test the quality of the MgO layer. Finally, the critical current density of the YBCO films was 6 MA/cm2 (77 K, 500 nm, self-field), indicating that this research provides a high-quality MgO substrate for the YBCO layer.

Growth of textured MgO through e-beam evaporation and inclined substrate deposition

Preparation of MgO Self-Epitaxial Films for YBCO High-Temperature Coated Conductors

Influence of Substrate Temperature and Deposition Rate on the Texture and Surface Morphology of ISD–MgO

Biaxial Texture Evolution in MgO Films Fabricated Using Ion Beam-Assisted Deposition

Heteroepitaxial Growth of MgO Films by Dual Ion Beam Sputtering

Fabrication of long-length ion beam-assisted deposited MgO templates for YBCO-coated conductors

A Method to Fabricate Biaxially Textured MgO Buffer Layer for HTS Coated Conductor

Fabrication of Ibad-Mgo and Pld-Ceo2 Layers for Ybco Coated Conductors

Conformal MgO film grown at high rate at low temperature by forward-directed chemical vapor deposition

Biaxial Texture Establishment and Evolution in IBAD-MgO Films under Different Ion-to-atom Ratios

Reel-To-Reel Deposition of Epitaxial Double-Sided Mgo Buffer Layers for Coated Conductors

Growth of high quality large area MgB2 thin films by reactive evaporation

Development of Textured Magnesium Oxide Templates on Amorphous Polymer Surfaces Using Ion-Beam-Assisted-Deposition

Surface Scaling Analysis of Textured MgO Thin Films Fabricated by Energetic Particle Self-Assisted Deposition

Preparation of Epitaxial MgO Films Deposited by RF Magnetic Sputtering on the IBAD-MgO Substrate

Preparation of Double-Sided MgO Template for YB2Cu3O7-δ Coated Conductors

The Electrical and Morphological Properties of Magnesium Oxide/alumina Bilayered Thin Films Prepared by Electron Beam Evaporation at Oblique Incidence

Characteristics of 4-Inch (100) Oriented Mg-doped Β-Ga2o3 Bulk Single Crystals Grown by a Casting Method

Microstructure Evolution of Homoepitaxial MgO Layer and the Effect on the Growth Mode of CeO2 Film

Crystallographic Texture of MgO and its Effect on the Growth of BaTiO<sub>3</sub> Thin Films by RF Sputtering

Epitaxial Growth and Characterization of RF-Sputtered LaMnO 3 Cap Layers on Homo-Epi MgO/IBAD–MgO Templates