Abstract:Silicon based power micro-electro-mechanical system (MEMS) applications require highspeed microrotating machinery operating stably over a large range of operating conditions. The technical barriers to achieving stable high-speed operation with micro-gas-bearings are governed by (1) stringent fabrication tolerance requirements and manufacturing repeatability, (2) structural integrity of the silicon rotors, (3) rotordynamic coupling effects due to leakage flows, (4) bearing losses and power requirements, and (5) transcritical operation and whirl instability issues. To enable high-power density the micro-turbomachinery must be run at tip speeds comparable to conventional scale turbomachinery. The rotors of the micro-gas turbines are supported by hydrostatic gas journal and hydrostatic gas thrust bearings. Dictated by fabrication constraints the location of the gas journal bearings is at the outer periphery of the rotor. The high bearing surface speeds (target nearly 10 x 10(6) mm rpm), the very low bearing aspect ratios (L/D < 0.1), and the laminar flow regime in the bearing gap (Re < 500) place these micro-bearing designs into unexplored regimes in the parameter space. A gas-bearing supported micro-air turbine was developed with the objectives of demonstrating repeatable, stable high-speed gas-bearing operation and verifying the previously developed micro-gas-bearing analytical models. The paper synthesizes and integrates the established micro-gas-bearing theories and insight gained from extensive experimental work. The characteristics of the new micro-air turbine include a four-chamber journal bearing feed system to introduce stiffness anisotropy, labyrinth seals to avoid rotordynamic coupling effects of leakage flows, a reinforced thrust bearing structural design, a redesigned turbine rotor to increase power, a symmetric feed system to avoid flow and force nonuniformity, and a new rotor micro-fabrication methodology for reduced rotor imbalance. A large number of test devices were successfully manufactured demonstrating repeatable bearing geometry. More specifically, three sets of devices with different journal bearing clearances were produced to investigate the dynamic behavior as a function of bearing geometry. Experiments were conducted to characterize the "as-fabricated" bearing geometry, the damping ratio, and the natural frequencies. Repeatable high-speed bearing operation was demonstrated using isotropic and anisotropic bearing settings reaching whirl-ratios between 20 and 40. A rotor speed of 1.7 x 10(6) rpm (equivalent to 370 m/s blade tip speed or a bearing DN number of 7 x 10(6) mm rpm) was achieved demonstrating the feasibility of MEMS-based micro-scale rotating machinery and validating key aspects of the micro-gas-bearing theory. [DOI: 10.1115/1.3123343]

Rotordynamic characteristics of a micro turbo generator supported by air foil bearings

Evaluation of Foil Bearing Performance and Nonlinear Rotordynamics of 120 kW Oil-Free Gas Turbine Generator

Numerical and Experimental Studies on Stability of Cryogenic Turbo-Expander with Protuberant Foil Gas Bearings

Numerical investigation on the rotordynamics of a high-speed air compressor supported by gas foil bearings

Dynamic analysis of a high-speed micro compressor supported by spiral-grooved hydrodynamic air bearing

Study on the rotordynamics of a high-speed motor supported by air foil bearings

Stability and Vibration Characteristics of A Rotor-Gas Foil Bearings System with High-Static-Low-Dynamic-Stiffness Supports

Investigations on the nonlinear dynamic characteristics of a rotor supported by hybrid foil magnetic bearings

Effects of bearing clearance and supporting stiffness on performances of rotor-bearing system with multi-decked protuberant gas foil journal bearing

Dynamic and stability comparison analysis of the high-speed turbocharger rotor system with and without thrust bearing via machine learning schemes

Performance Of An Active Electric Bearing For Rotary Micromotors

High-Speed Operation of a Gas-Bearing Supported MEMS-Air Turbine

Study on Dynamics of Micro Gas Journal Bearing--rotor System

An optimal parameter identification approach in foil bearing supported high-speed turbocharger rotor system

Rotor dynamic experimental investigation of an ultra-high-speed permanent magnet synchronous motor supported on a three-pad bidirectional gas foil bearing

Nonlinear Dynamic Analysis of a Rotor-Porous Air Journal Bearing System With O-Rings Mounted

Simulation and Experimental Verification of Dynamic Characteristics on Gas Foil Thrust Bearings Based on Multi-Physics Three-Dimensional Computer Aided Engineering Methods

A Novel Method for Calculating the Dynamic Force Coefficients of Gas Foil Bearings and Its Application in the Rotordynamic Analysis

Modeling and Analysis of A Micromotor with an Electrostatically Levitated Rotor

Parametric study on static and dynamic characteristics of bump-type gas foil thrust bearing for oil-free turbomachinery

A review on recent advancements in an automotive turbocharger rotor system supported on the ball bearings, oil film and oil-free bearings