Abstract:Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Ahead of Print. This research aims to analyze the welding of 1 mm thick NiTinol sheets using an autogenous double pulse tungsten inert gas (DPTIG) welding process. The effect of heat input (HI) on bead geometry, microstructure, hardness, tensile strength, phase transformation temperature (PTT), and corrosion behavior was studied. The lower (111.25 J/mm), and higher (120.14 J/mm) HI produced an average grain size of 26 μm and 36 μm, respectively. The microstructure of the fusion zone (FZ) had coarser columnar grains with intermetallic phases such as Ni3Ti, and TiO2. The grain size in the FZ increased with the increase in HI. Sample P (111.25 J/mm) showed a higher hardness of 280.54 HV and tensile strength of 566 MPa due to a higher proportion of austenite phase (99.4%), the smaller grain size of 26 μm, a larger fraction of high angle grain boundary (HAGB) of 75.8%, and higher kernel average misorientation (KAM) value of 4.93. Compared to base metal (BM), sample P (111.25 J/mm), and sample S (120.14 J/mm) exhibited a reduction in tensile strength of 19.14% and 32.29%, respectively. The decline in hardness and tensile strength was attributed to the formation of intermetallic phases, a decrease in the Ti/Ni ratio, coarser grain formation, and a decrease in HAGB fraction and KAM values. The fractured tensile samples showed a mixed mode of fracture with dimples and cleavage facets. Compared to BM, Sample Q (118.05 J/mm) exhibited lesser variation in temperature hysteresis values for austenite and martensite temperatures, with a deviation of 0.4°C and 3.1°C, respectively. All the welded samples had better corrosion behavior than the BM due to a higher Ti/Ni ratio.

Effect of heat treatment into tensile strength, hardness and microstructural attributes of TIG welded Ti-6Al-4V titanium alloy

The effect of heat treatment system on mechanical properties of titanium alloy BTi-6554

Micromechanical testing and microstructure analysis of as-welded and post-weld heat-treated Ti-6Al-4V alloy

Effect of heating treatment on the microstructural evolution and dynamic tensile properties of Ti-6Al-4V alloy produced by selective laser melting

Investigation of post-weld heat treatment (T6) and welding orientation on the strength of TIG-welded AL6061

Exploring the Heat Treatment Parameters, Microstructural Evolution, and Mechanical Properties of Ti–6Al–4V Alloy Fabricated by a Selective Laser Melting Process

Microstructure Evolution and Mechanical Properties of TA15/Ti60 Tailor Welded Blank by Electron Beam Welding

Effects of heat input on microstructure evolution, mechanical and corrosion properties of TC4 alloy by keyhole TIG welding

Study On The Impact Of Post Weld Heat Treatment On Tig And A-Tig Inconel 617 Weldments

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Additive Manufactured Ti-6.5Al-2Zr-1Mo-1V Alloy

The Effect of Annealing and Cryogenic Treatment on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy

Microstructural evolution and microhardness of a selective-laser-melted Ti–6Al–4V alloy after post heat treatments

Effect of Solution Treatment and Cooling Rate on the Microstructure and Hardness of Ti-6Al-4V Alloy Manufactured by Selective Laser Melting Before and After Hot Isostatic Pressing Treatment

Effect of Heat Treatment on Microstructure and Mechanical Properties of Titanium Alloy Fabricated by Laser–Arc Hybrid Additive Manufacturing

Effect of Heat Treatments on Mechanical Properties and Wear Resistance of Laser-Powder Bed-Fused Ti6Al4V Alloy

The effect of heat input on weld-bead geometry, mechanical, phase transformation temperature, and corrosion properties of autogenous double pulse TIG welded nitinol sheets

Mechanisms of heat treatment and ductility improvement of high-oxygen Ti–6Al–4V alloy fabricated by metal injection molding

Effects of different heat treatment temperatures on the microstructure and mechanical properties of additive manufacturing Ti65 alloys

Microstructure and Mechanical Properties of Welded Joints of Titanium Alloy Ti60 after Laser Welding and Subsequent Heat Treatment

Laser Additive Manufactured Ti–6Al–4V Alloy: Heat Treatment Studies

Effect of DC Micro-Pulsing on Microstructure and Mechanical Properties of TIG Welded Ti-6Al-4V