Abstract:This work compares the performance of dispersive liquid–liquid method (DLLME) as a prior step for determining copper by flame atomic absorption spectrometry (FAAS), when using the ionic liquid (IL) 1-butyl-3-methylimidazolium hexafluorophosphate (C4MIm-PF6) or the IL-based surfactant 1-hexadecyl-3-butylimidazolium bromide (C16C4Im-Br) as extractant solvents. For the water-insoluble C4MIm-PF6, the most conventional DLLME mode using acetonitrile as dispersive solvent was employed. For the water-soluble C16C4Im-Br, the in situ DLLME mode with lithium bis[(trifluoromethane)sulfonyl]imide (Li-NTf2) as metathesis reagent was employed. In both approaches, some effective parameters such as volumes of extractant and dispersive solvents, concentration of complexing agent, pH of sample solution, salting-out effect and final diluting solvent to ensure compatibility with FAAS, were properly optimised. The optimum conditions for the IL-DLLME method using C4MIm-PF6 were: 100 μL of neat C4MIm-PF6, 1 mL of acetonitrile, 10 mL of water, no control of pH for environmental waters, NaCl content of 23 g L−1, diethyl dithiocarbamate (DDTC) as complexing agent at 10 mg L−1 and final dilution of the micro-droplet with acetonitrile up to 70 µL. The optimum conditions for the in situ IL-DLLME method using C16C4Im-Br were: 0.8 mL of acetonitrile, 10 mL of water containing C16C4Im-Br at 25.2 mmol L−1, final dilution step of the micro-droplet with 200 µL of acetonitrile and remaining conditions as those of C4MIm-PF6. The analytical performance of both methods was similar, being slightly better for the IL-DLLME method using C4MIm-PF6, with limits of detection (LOD) of 3.3 µg L−1 (versus 5.1 µg L−1 when using C16C4Im-Br), precision values as intraday relative standard deviation (RSD in %) lower than 8.8% (being of 10% for the C16C4Im-Br method) and an enrichment factor of 54 (being 27 when using C16C4Im-Br). The DLLME-FAAS method with C4MIm-PF6 was used in the analysis of environmental waters with successful performance, with relative recoveries of 110% and 105%, and interday precision with RSD values of 21% and 7.4% for spiked levels of 60 and 160 µg L−1, respectively. The results obtained when analysing an urban wastewater sample coming from an inter-laboratory exercise was comparable to those obtained for other 93 laboratories. The method was also valid for the determination of Cu2+ in presence of foreign ions commonly found in natural waters.

Investigation of regularities of ion flotation of copper with the use of sodium diethyldithiocarbamate

Exploring Dextrin As an Eco-Friendly Depressant for Selective Flotation Separation of Scheelite and Calcite Minerals

A thermodynamic approach to ion flotation. I. Kinetics of cupric ion flotation with alkylsulfates

Efficient removal of heavy metals from aqueous solutions using ion flotation technique

Removal of copper ions in polluted waters by DTC heavy metal chelator

Removal of Copper from Industrial Wastewater by Ion Flotation with Sodium Dodecyl Sulfate as Anionic Collector

Removal of cadmium (II) from simulated wastewater by ion flotation technique

REMOVAL OF COPPER ION FROM WASTEWATER BY FLOTATION

Ion Flotation of Copper(II) and Lead(II) from Environmental Water Samples

An Insight into Properties and Mechanisms of a Dithiocarbamate Chelating Agent for the Removal of Toxic Metal Ions from Metallic Mine Wastewater

Removal of Micro Complex Copper in Aqueous Solution with a Dithiocarbamate Compound

Experimental and theoretical studies of sodium acetyldithiocarbamate for the removal of Cu2+ and Ni2+ from aqueous solution

Ion flotation of heavy metal ions by using biodegradable biosurfactant as collector: Application and removal mechanism

The effect of triethylenetetraamine (Trien) on the ion flotation of Cu2+ and Ni2+

Synthesis of Magnetic Dithiocarbamate Chelating Resin and Its Absorption Behavior for Ethylenediaminetetraacetic Acid Copper

Superabsorbents and Their Application for Heavy Metal Ion Removal in the Presence of EDDS

Inhibition of Copper Corrosion in Sodium Chloride Solution by the Self-Assembled Monolayer of Sodium Diethyldithiocarbamate

Removal of trace quantities of cadmium from aqueous iodide solutions by ion flotation

Ionic liquids versus ionic liquid-based surfactants in dispersive liquid–liquid microextraction for determining copper in water by flame atomic absorption spectrometry

Solid Phase Extraction–High-Performance Liquid Chromatography Detection of Organic Additives in Acidic Copper Baths II. Polyethylene-Glycol Based Suppressors