Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

Intervening Interfacial Reaction Between Refractory and Rare Earth-Bearing Molten Steel by Pulsed Electric Current to Inhibit the Clogging of Submerged Entry Nozzle

Influence of Interface Electric Field on Interaction Between Molten Iron and Refractory Interface

Explore on the Mechanism of Action between Al2O3–SiO2 Refractory Materials and Rare Earth High Carbon Heavy Rail Steel

Reaction mechanism between Al2O3–MgO refractory materials and rare earth high-carbon heavy rail steel

Investigation of the erosion mechanism of the mold flux containing rare earth oxide on the submerged entry nozzle affected by an external electric field

Controlling the Electric Field Characteristics to Suppress the Clogging and Corrosion of the Continuous Casting Nozzle

Effect of CeAlO3 refractories on the cleanliness of rare earth treated steel

Influence of Interface Electric Field on Wettability Between Molten Iron and Submerged Entry Nozzle Interface

Influence of Pulse Current on Inclusion Properties of Alumina in Molten Steel

Agglomeration behavior of rare earth inclusions and alumina inclusions at the interface between argon and molten steel

Steel–refractory reactions in lanthanum-, cerium-, and yttrium-added steels

The effect of rare earth on microstructure and wear resistance of plasma electrolytic carburizing layer on 17–4PH stainless steel

Interaction Behaviors of Ce‐Treated Al‐Killed Steel Grades with Different Refractories

Dynamic interaction of refractory and molten steel: Corrosion mechanism of alumina-magnesia castables

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

Influence of Refractory-Steel Interfacial Reaction on the Formation Behavior of Inclusions in Ce-containing Stainless Steel

Formation of ferrospinel layer at the corroded interface between Al 2 O 3 ‐spinel refractory and molten steel in RH refining ladle

Effect of interfacial reaction behaviour on the clogging of SEN in the continuous casting of bearing steel containing rare earth elements

Analysis on clogging of submerged entry nozzle in continuous casting of high strength steel with rare earth

Effect of Steel-refractory Reactions on Removal of Arsenic from Molten Steel with Lanthanum Additions