Abstract:Conductive films of carbon nanofibers (CNFs) decorated/coated with metals, either silver (Ag) or nickel (Ni) are fabricated using a solution casting process and used as novel heating elements (HEs) for induction welding of carbon fiber/polyphenylene sulfide (CF/PPS) thermoplastic composites. Prior to making the films, the metal‐coated CNFs are prepared by an electroless plating method using Ag or Ni precursors. A solution of the metal‐coated CNFs is then casted onto a pure PPS film to give a robust conductive film upon solvent evaporation and annealing in an oven at 200 °C. SEM observation and electrical resistivity measurements reveal that the CNFs are successfully coated with the metals which result in a significant decrease of the films’ electrical resistivity. A third type of HE is also fabricated by solution mixing Ag‐coated CNFs and magnetic Fe3O4 nanoparticles. The welding efficiency of the fabricated films is assessed for induction welding of two different types of thermoplastic composites, that is, unidirectional pre‐impregnated 16 plies of CF/PPS compression‐molded in a quasi‐isotropic stacking sequence and 8‐ply of satin weave fabric CF/PPS compression‐molded in a cross‐ply stacking sequence. The mechanical apparent lap shear strength (LSS) of the induction‐welded joints is evaluated for the fabricated HEs and compared with the LSS of joints welded using conventional stainless steel mesh susceptors. Under similar testing conditions, Ag‐coated CNFs HEs lead to the highest LSS with an average value of ≈31.5 MPa. In general, the new HEs result in superior LSS and higher heating rates when compared to the metallic mesh counterparts. The present work offers a new perspective to push the boundaries toward high quality welding of thermoplastic composites using nanomaterials‐based HEs. Novel heating element (HE) types are developed and used for induction welding of thermoplastic composites. The HEs are fabricated using carbon nanofibers (CNFs) that are coated/decorated with metals, either silver or nickel by an electroless plating method. The realization of such HEs leads to the achievement of high quality welding with mechanical apparent lap shear strength values exceeding that obtained for the commonly‐used stainless steel mesh susceptors.

Material Selection Methodology for an Induction Welding Magnetic Susceptor Based on Hysteresis Losses

Characterization of Magnetic Susceptor Heating Rate Due to Hysteresis Losses in Thermoplastic Welding

A comprehensive study of metal-coated short carbon fibers, graphite particles, and hybrid fillers for induction heating

High-susceptibility nanoparticles for micro-inductor core materials

Novel Heating Elements for Induction Welding of Carbon Fiber/Polyphenylene Sulfide Thermoplastic Composites

An Inductive Method for Comprehensive Estimation of Temperature-Dependent Electrical and Thermal Properties of Conductive Ferromagnetic Materials

Formulation and mixing conditions of magnetic composite materials used for magnetic wedges in an interior permanent magnet synchronous motor

Numerical simulations of strengthen induction heating with response surface methodology

Investigation of Induction Heating Process for Selective Melting of Aluminum Alloy for the Repair of Exit Hole Defect in Friction Stir Welding Process

Physical simulation and computational modelling for validation of soft magnetic composite impeder performance

Multifunctional Polymer Composites for Automatable Induction Heating with Subsequent Temperature Verification

Microscopic level modeling of induction welding heating mechanisms in thermoplastic composites

Influence of welding-induced mechanical stress on the electromagnetic properties of magnetic lamination

Numerical Simulation of the Moving Induction Heating Process with Magnetic Flux Concentrator

Multiphysics modeling and experimental validation of heat and mass transfer for the vacuum induction melting process

Comparative Investigation of Phenomenological Modeling for Hysteresis Responses of Magnetorheological Elastomer Devices

Hysteresis in Magnetic Shape Memory Composites: Modeling and Simulation

Modeling And Simulation Of Induction Heating With Magnetic Flux Concentrator

Thermistors Based on Polyethylene Composites with γ‐Fe2O3/Multiwalled Carbon Nanotube Hybrid Fillers for Protection of Electronic Circuits

Study on the Plane Induction Heating Process Strengthened by Magnetic Flux Concentrator Based on Response Surface Methodology

Development of Induction Heating System Ensuring Increased Heating Efficiency of the Charge Material in a Forging