Abstract:This paper discusses the applicability of J.L. Straalsund et al.'s technique for combining the Larson–Miller parameter (LMP) and life-fraction rule to form a single high-temperature strength equation for 9Cr-oxide-dispersion-strengthened (ODS) tempered martensitic steels (TMS). It uses the extensive dataset on creep rupture, tensile, and temperature-transient-to-burst tests of 9Cr-ODS TMS cladding tubes in the α-phase, α/γ-duplex, γ-phase matrices, which are accumulated by the Japan Atomic Energy Agency so far. The technique is adequately applicable to 9Cr-ODS TMS cladding tubes. A single high-temperature strength equation expressing the mechanical strength in different deformation and rupture modes (creep, tensile, temperature-transient-to-burst) is derived for 9Cr-ODS TMS cladding tubes. This equation can predict the rupture life of the cladding tubes under various stresses and temperatures over time. The applicable range of the high-temperature strength equation is specified in this study and the upper limit temperature for the equation is found to be 1200°C. At temperatures higher than 1200°C, the coarsening and aggregation of nanosized oxide particles and the γ to δ phase transformation are reported in previous studies. The high-temperature strength equation can be well applied to the creep and tensile strength in the α-phase matrix, the creep strength in the γ-phase matrix and the temperature-transient-to-burst strength in both phases except for the low equivalent stress (43 MPa) at temperatures exceeding 1050°C. The mechanism of the notable consistency between creep and tensile strength in the α-phase matrix is discussed by analyzing the high-temperature deformation data in the light of existing deformation models. The study suggested the thermal activation process is dominant even for the high-temperature deformation modes exceeding yield stress in the 9Cr-ODS TMS with the fine-grained matrix.

High-Temperature Stress-Rupture Properties of a Ferritic Steel for Solid Oxide Fuel Cell Interconnect

Low Cycle Fatigue and Creep Fatigue Interaction Behavior of 9Cr-0.5Mo-1.8w-v-nb Heat-Resistant Steel at High Temperature

Low Cycle Fatigue Behavior of Original Ferritic P92 Steel at High Temperature: Experiments and Simulations

Characterization of Low Cycle Fatigue Performance of New Ferritic P92 Steel at High Temperature: Effect of Strain Amplitude

Creep Fracture Behavior of the Crofer 22 APU for the Interconnect of Solid Oxide Fuel Cell under Different Temperatures

Characterization of Low Cycle Fatigue of Ferritic–Martensitic P92 Steel: Effect of Temperature

Fatigue-Creep Interaction Of P92 Steel And Modified Constitutive Modelling For Simulation Of The Responses

Characterization of the Cyclic Softening and Remaining Creep Behaviour of P92 Steel Weldment

Low cycle fatigue and creep-fatigue interaction behavior of 2.25CrMoV steel at high temperature

Creep Rupture Behavior in Dissimilar Weldment Between FB2 and 30cr1mo1v Heat-Resistant Steel

Influence of Cr Content on the Mechanical, Oxidation, and Electrical Properties of Powder Metallurgy Ferritic Stainless Steel for Solid Oxide Fuel Cell Interconnect

Study on creep damage and life prediction of the planar solid oxide fuel cell by modeling of multiphysics coupled

Initial stage oxidation corrosion of commercial ferritic stainless steels with different Cr contents at 650 °C for solid oxide fuel cells

Combined crystal plasticity and grain boundary modeling of creep in ferritic-martensitic steels: I. Theory and implementation

Study on the High Temperature Creep Behavior of 30Cr25Ni20 Heat-Resistant Steel

Ferritic Steel Interconnect Used in Solid Oxide Fuel Cell

Experimental Investigations On Mechanical Properties Of A High Cr Ferritic Steel For Usc Steam Turbine Rotor

Assessment of creep rupture properties for dissimilar steels welded joints between T92 and HR3C: CREEP PROPERTIES OF T92/HR3C WELDED JOINTS

The effect of surface treatment on the oxidation of ferritic stainless steels used for solid oxide fuel cell interconnects

Formulation of high-temperature strength equation of 9Cr-ODS tempered martensitic steels using the Larson–Miller parameter and life-fraction rule for rupture life assessment in steady-state, transient, and accident conditions of fast reactor fuel

Creep Characteristics and Oxidation Behavior of New-Styled Ferrite Heat Resistant Steel at 650℃