Abstract:Abstract. The mining system has the potential for mining water problems that have an impact on the entry of water into the mine openings, thus affecting working conditions with a decrease in rock strength resulting in instability. The mining water problem occurred at PT PPA Site Job PT MLP disposal area and pit. This research was conducted to determine the value of the actual rock strength (strength material), runoff water management in the form of determining the dimensions of the drains, sump dimensions, the number and specifications of the pump to be used, and the value of the safety factor (FK) on the slopes. The research method used is the geotechnical analysis of slope stability with the Finite Element Method and the Limit Equilibrium Method and is simulated with Phase2 and Slide software. The study was conducted in the disposal area divided into 5 sections (A-E). The input material parameters used are the internal shear angle (Ø), cohesion (c) and the density of the embankment material (ɤ) which are obtained based on the results of testing the physical and mechanical properties of the bulk and core samples. Runoff water management is carried out by hydrological analysis using the Gumbel distribution method and the Mononobe equation, while the planning of the dimensions of the water channel uses the Manning formula and the sump dimension by trial and error based on the amount of water discharge entering the pit. The test results show the lowest cohesion (c) value is 0.22 kg/m2 and the lowest internal shear angle (Ø) is 15.30o. Hydrological analysis for recommendations for the dimensions of waterways in the management of runoff water outside the pit, namely the width of the base (B) 0.4 meters; optimal water height (h) 0.21 meters; channel height (H) 0.45 meters and top length (L) 0.90 meters. The dimensions of the sump in the management of runoff and groundwater in the pit are 26 meters long, 19 meters wide and 6 meters high with a volume capacity of 2,964 m3, and the pump used is Multiflo® RF-420EXHV which has specifications with a maximum rotation speed of 1700 rpm, head 250 meters and pumping capability of 450 l/s. Geotechnical analysis in the disposal area shows that section A of the slopes (a) and E and in the area of the pit section Y there is no need for slope geometry recommendations based on KEPMEN 1827K/MEM/30/2018 with a safety factor value (FK) 1,3. Abstrak. Sistem penambangan memiliki potensi permasalahan air tambang yang berdampak dengan masuknya air kedalam bukaan tambang sehingga mempengaruhi kondisi kerja dengan penurunan kekuatan batuan yang mengakibatkan ketidakstabilan. Permasalahan air tambang tersebut terjadi pada PT PPA Site Job PT MLP area disposal dan pit. Penelitian ini dilakukan untuk mengetahui nilai kekuatan batuan (strength material), pengelolaan air limpasan berupa penentuan dimensi saluran air, dimensi sump, jumlah dan spesifikasi pompa yang akan digunakan, serta nilai faktor keamanan (FK) pada lereng. Metode penelitian yang digunakan adalah analisis geoteknik kestabilan lereng dengan metode elemen hingga (Finite Element Method) dan metode kesetimbangan batas (Limit Equilibrium Method) serta disimulasikan dengan software Phase2 dan Slide. Penelitian dilakukan pada area disposal yang dibagi menjadi 5 section (A-E). Input parameter material yang digunakan adalah sudut geser dalam (Ø), kohesi (c) dan berat jenis material timbunan (ɤ) yang diperoleh berdasarkan hasil pengujian sifat fisik dan sifat mekanik pada bulk dan core sample. Pengelolaan air limpasan dilakukan dengan analisis hidrologi menggunakan metode Distribusi Gumbel dan persamaan Mononobe, sedangkan perencanaan dimensi saluran air menggunakan rumus Manning dan dimensi sump dengan trial and error berdasarkan jumlah debit air yang masuk ke dalam pit. Hasil pengujian menunjukkan nilai kohesi (c) terendah sebesar 0,22 kg/m2 dan nilai sudut geser dalam (Ø) terendah sebesar 15,30o. Analisis hidrologi untuk rekomendasi dimensi saluran air dalam pengelolaan air limpasan di luar pit yaitu lebar dasar (B) 0,4 meter; tinggi air optimal (h) 0,21 meter; tinggi saluran (H) 0,45 meter dan panjang atas (L) 0,90 meter. Dimensi sump dalam pengelolaan air limpasan dan air tanah di dalam pit yaitu panjang 26 meter, lebar 19 meter dan tinggi 6 meter dengan kapasitas volume 2.964 m3, serta pompa yang digunakan adalah Multiflo® RF-420EXHV memiliki spesifikasi dengan kecepatan putaran maksimal 1700 rpm, head 250 meter dan kemampuan pemompaan 450 l/s. Analisis geoteknik pada area disposal menunjukkan section A lereng (a) dan E serta pada area pit section Y tidak diperlukannya rekomendasi geometri lereng berdasarkan KEPMEN 1827K/MEM/30/2018 dengan nilai faktor keamanan (FK) ≥ 1,3.

Excavation method and support system in the diversion tunnel of Tiga Dihaji Dam, South Sumatera, Indonesia based on the rock mass quality

Application of RMR, Q, and Japanese Rock Mass Classification Systems for Design of Support Systems of the Narogong Weir Diversion Tunnel, West Java, Indonesia

Rock mass classification for design of excavation method and support system of tunnel 1 Sigli-Aceh toll road, Indonesia

Instability Mechanism of Shallow Tunnel in Soft Rock Subjected to Surcharge Loads

Empirical design for the excavation method and support system at tunnel no 2, Bintang Bano irrigation area, West Nusa Tenggara

Geological Mapping and Stand-up Time Estimation based on Core Drilling Evaluation using Rock Mass Rating Method on The Main Spillway and Diversion Tunnel at Manikin Dam, Kupang Regency, Nusa Tenggara Timur

Numerical Analysis of Slope Stability Due to Excavation of Diversion Tunnel at Pamukkulu Dam Site, Indonesia

Rock Mass Classifications of Flysch Deposits for Analyses of Tunnel Behaviour and Support System-A Case Study of Design Evaluation of Tunnel 6 of Jakarta-Bandung High-Speed Railway

Numerical evaluation of support design: A case study Jakarta – Bandung, Indonesia High-Speed Railway Tunnel 7

EVALUASI PERBAIKAN PONDASI KONDUIT DENGAN METODE GROUTING

Seepage handling using secant pile as a solution to replace curtain grouting and dam stability evaluation to optimize work on the Margatiga Dam construction project

Study on the Stress and Deformation of Surrounding Rock and Support Structure of Super Large Section Tunnels Based on Different Excavation Methods

Tunnel Support Validation Using Numerical Modelling: A Case Study from NW, Himalaya, India

Support System for Tunnelling in Squeezing Ground of Qingling-Daba Mountainous Area: A Case Study from Soft Rock Tunnels

Curtain Grouting Test On Volcanic Breccia Foundation As An Effort To Assess The Effectiveness Of Grouting Case Study: Construction Of Minting Dam

Evaluation of Lateral and Axial Deformation for Earth Pressure Balance (EPB) Tunnel Construction Using 3 Dimension Finite Element Method

SEEPAGE ANALYSIS ON THE EMBANKMENT BODY ZONAL TYPE DAM IN BAGONG EAST JAVA INDONESIA

Mitigation of tunnel support design risks for hydropower projects within high tectonic stress regimes – an empirical analysis

Model Design and Application for Excavation Face Stability in Upward Shield Tunneling

Analysis of Ground Surface Settlement Induced by the Construction of a Large-Diameter Shallow-Buried Twin-Tunnel in Soft Ground

Optimalisasi Material Strength Properties Timbunan untuk Kestabilan Lereng Timbunan PT Putra Perkasa Abadi, Site Job PT Makmur Lestari Primatama, Kecamatan Langgikima, Kabupaten Konawe Utara, Provinsi Sulawesi Tenggara