Abstract:A normal composite wall panel is a structural component composed of polystyrene insulation boards and concrete surface layers reinforced with steel wire mesh. It can be entirely prefabricated in a factory or constructed with the concrete surface layers cast on-site. A novel prefabricated monolithic concrete–polystyrene panel composite wall panel (CPC wall panel) is proposed in this study. The CPC panel features a middle part that is prefabricated in the factory while the reinforced concrete regions at its two side ends are cast on-site. To evaluate the seismic performance of the wall panel, 18 CPC specimens were designed, manufactured, and quasi-statically tested, through which the structural behaviors, failure mode, and load-bearing capacity were studied. In addition, the influences of the height-to-width ratio and the vertical compressive stress level on the seismic performance of the CPC panels were also investigated. The test results showed that the connectors spaced at 400 mm × 500 mm could ensure the concrete layers on both sides of the polystyrene board worked collectively under seismic conditions. When subjected to lateral loads, the interface between the newly poured concrete and the existing concrete exhibited good bonding. Moreover, the failure mode of the CPC wall panel was largely correlated to the height-to-width ratio that, for specimens having four steel bars of 12 mm diameter and a height-to-width ratio greater than 1, the flexural failure was initially developed, followed by diagonal shear failure. In specimens with a height-to-width ratio of 1, flexural and diagonal shear failures occurred almost simultaneously. For specimens with a height-to-width ratio of less than 1, the final diagonal shear failure was predominant. The longitudinal reinforcing bars at the two ends of the CPC panels could effectively improve their lateral load-bearing capacity, with the enhancement influenced by the height-to-width ratio, the vertical load applied to the wall panel, and the cross-sectional area of the steel bars. In practice, the lateral load-bearing capacity of the CPC panel can be conservatively evaluated using the calculation method of the reinforced concrete shear walls. Finally, the ductility of the CPC specimens was affected by the height-to-width ratio and the axial compressive stress level, such that the specimens with a larger height-to-width ratio and lower axial compressive stress exhibited better ductility.

Experimental study on seismic performance of new foam concrete composite wall panel based on nanomaterials

Seismic Behavior of Composite Shear Walls Incorporating Concrete-Filled Steel and FRP Tubes As Boundary Elements

Seismic Performance of Reinforced Concrete Squat Walls with Embedded Cold-Formed and Thin Walled Steel Truss

Experimental Study on Seismic Performance of Prefabricated Monolithic Concrete–Polystyrene Panel Composite Wall Panels

Mechanical performance of prefabricated lightweight steel-foamed ceramsite concrete wall panels: Experimental and theoretical investigations

Experiments and Numerical Simulations on the Seismic Performance of Steel-Frame Composite Wallboard Shear Walls

Experimental Investigation of Seismic Behavior of a New Type Masonry Walls

Experimental study on seismic performance of new-type fabricated shear wall with mortar connection

The model tests and numerical tests of out-plane seismic property of foam-in-place cavity wall

Experimental and theoretical study on seismic behavior of a new UHPFRC sandwich wall and wall-wall joint

Experimental Investigation of Effect of Section Configuration on Seismic Performance of an Innovative Integrated Concrete Masonry Wall System

Research advances of composite shear walls with double steel plates and filled concrete

Experimental Study on Seismic Performance of Fabricated Steel Foamed Concrete T-Shaped Wallboard

Application of Cement-Based Composite Nanomaterials in Prefabricated Thin-Wall Light Steel Structure Composite Wall

Experimental Study on Mechanical Property of a New Type of Sandwich Wall

Research on Mechanical Properties and Microstructures of Composite Wall Panels Made of High-Performance Fiber Reinforced Cement-based Composites

Experimental Investigation On The Seismic Behavior Of Newly-Developed Precast Reinforced Concrete Block Masonry Shear Walls

Experimental Study on Seismic Performance of Composite Shear Wall with Horizontal Connection and Frame

Experimental and numerical study on seismic performance of prefabricated new fly ash foam concrete structure

Experimental test for mechanical properties of new tenon composite wall using thermal self-insulation block

Experimental Study on Seismic Behaviour of an Unreinforced Precast Wall-Slab Structure Based on UHPC Sandwich Panels