Abstract:The present work deals with the dilatometric study of a hot-rolled 0.2C3Mn1.5Si lean medium Mn steel, mainly suitable for the quenching and partitioning (Q&P) heat treatment in both hot-rolled or cold-rolled condition, subjected to a variation of austenitization temperature. These investigations were performed in a temperature range of 800–1200 °C. In this context, the martensite transformation start temperature (Ms) was determined as a function of austenitization temperature and in turn obtained prior austenite grain size (PAGS). The results show rise in prior austenite grain size due to increasing austenitization temperature, resulting in elevated Ms temperatures. Measured dilatation curves were confronted with the metallographic analysis by means of scanning electron microscopy (SEM). The present paper also focuses on the construction of a continuous cooling transformation (CCT) and deformation continuous cooling transformation (DCCT) diagram of the investigated lean medium Mn steel in a range of cooling rates from 100 to 0.01 °C/s and their subsequent comparison. By comparing these two diagrams, we observed an overall shift of the DCCT diagram to shorter times compared to the CCT diagram, which represents an earlier formation of phase transformations with respect to the individual cooling rates. Moreover, the determination of individual phase fractions in the CCT and DCCT mode revealed that the growth stage of ferrite and bainite is decelerated by deformation, especially for intermediate cooling rates. Microstructural changes corresponding to cooling were also observed using SEM to provide more detailed investigation of the structure and present phases identification as a function of cooling rate. Moreover, the volume fractions obtained from the saturation magnetization method (SMM) are compared with data from X-ray diffraction (XRD) measurements. The discussion of the data suggests that magnetization measurements lead to more reliable results and a more sensitive detection of the retained austenite than XRD measurements. In that regard, the volume fraction of retained austenite increased with a decrease of cooling rate as a result of larger volume fraction of ferrite and bainite. The hardness of the samples subjected to the deformation was slightly higher compared to non-deformed samples. The reason for this was an evident grain refinement after deformation.

The Iron-Carbon Phase Diagram and Time-Temperature-Transformation (TTT) Diagrams

Iron–Carbon Phase Diagram

Computation of Isothermal Transformation Diagrams of 42crmo4 Steel from Dilatometer Measurements with Continuous Cooling

Interplay between diffusive and displacive phase transformations: TTT diagrams and microstructures

First Passage Times and Time-Temperature-Transformation curves for Martensites

The Time-Temperature Transformation Diagram Concerning Pure Bainite Formation in A Cu-Zn Alloy

Tailored Time-Temperature Transformation Diagram for IN718 Alloy Obtained via Powder Bed Fusion Additive Manufacturing: Phase Behavior and Precipitation Dynamic

Continuous Cooling Phase Transformation Rule of 20crmnti Low-Carbon Alloy Steel

Transition Between Alloy–element Partitioned and Non-Partitioned Growth of Austenite from a Ferrite and Cementite Mixture in a High-Carbon Low-Alloy Steel

Formulation of Austenite Continuous Cooling Transformation Curves for Austenite Phase of Steel

Analytical Modeling of Austenite Growth and Phase Evolution During Reverse Transformation from Pearlite in High Carbon Steels

Towards the ab initio based theory of the phase transformations in iron and steel

Austenite/Ferrite Interface Migration and Alloying Elements Partitioning: an Overview

Study of Phase Transformations and Interface Evolution in Carbon Steel under Temperatures and Loads Using Molecular Dynamics Simulation

Thermodynamic character of phase transformation of TCA titanium alloy electron beam welded joint

Austenite phase transformation of thermal analysis

Tracing Phase Transformation And Lattice Evolution In A Trip Sheet Steel Under High-Temperature Annealing By Real-Time In Situ Neutron Diffraction

Formation of Structure, Phase Composition and Properties in a Two-Phase Titanium Alloy Upon Variation of the Temperature and Rate Parameters of Heat Treatment

Austenite Decomposition of a Lean Medium Mn Steel Suitable for Quenching and Partitioning Process: Comparison of CCT and DCCT Diagram and Their Microstructural Changes

Computation of Phase Fractions in Austenite Transformation with the Dilation Curve for Various Cooling Regimens in Continuous Casting

Kinetics of Orthorhombic Martensite Decomposition in TC21 Alloy under Isothermal Conditions