Abstract:A dual phase (martensite–austenite) low carbon nickel-manganese transformation-induced plasticity (TRIP) steel was fabricated by heavily warm rolling (HWR), and the effect of annealing on the phase fraction, mechanical properties and tensile deformation behavior of the heavily warm rolled (HWRed) steel was investigated. The results showed that the reverse transformation of γ-austenite from α′-martensite occurs and that the γ-austenite volume fraction (VA) decreases from 91% to 55% as the annealing temperature increases from 400 °C to 800 °C, respectively. The HWRed steel annealed at 400 °C exhibits a high strength-high ductility combination with yield strength of 706 MPa, ultimate tensile strength (UTS) of 1573 MPa, total elongation (TEL) of 21.6%, and the product of the strength and elongation (PSE: UTS×TEL) is 34 GPa%. These excellent mechanical properties are principally attributed to the formation of a large volume fraction of austenite (γ) by the reverse transformation and subsequent TRIP effect during tensile deformation. It was found that the HWRed and annealed steels exhibit a special tensile behavior with a large yielding strain followed by pronounced strain hardening. The tensile curve can be readily divided into three obviously different stages. The strain-induced martensite (SIM) transformation (γ -α′) occurs in the early yielding deformation stage and in the intermediate rapidly hardening deformation stage, indicating that the TRIP effect dominates the process of these two stages. However, the retained γ-austenite remains very stable, and no TRIP effect is observed in the final hardening deformation stage. The load-unload reload (LUR) test was performed to evaluate the back stress (σb) hardening effect during tensile testing. It is believed that the pronounced strain hardening behavior after yielding is mainly associated with the σb enhancement induced by the strain partitioning between the soft retained γ-austenite and the hard α′-martensite due to the SIM transformation during tensile deformation.

Tracing Phase Transformation And Lattice Evolution In A Trip Sheet Steel Under High-Temperature Annealing By Real-Time In Situ Neutron Diffraction

In-situ Observation of Phase Transformation During Heat Treatment Process of High-Carbon Bainitic Bearing Steel

Micromechanical Behavior of Transformation‐Induced Plasticity‐Assisted Annealed Martensitic Steel Using in Situ Neutron Diffraction

The In Situ Observation of Phase Transformations During Intercritical Annealing of a Medium Manganese Advanced High Strength Steel by High Energy X-Ray Diffraction

Atom-probe tomographic and dilatometric studies of phase-transformations after inter-critical annealing of a low-carbon dual-phase steel

Microstructure Evolution and Mechanical Behavior of A Hot-Rolled High-Manganese Dual-Phase Transformation-Induced Plasticity/Twinning-Induced Plasticity Steel

Martensite phase stress and the strengthening mechanism in TRIP steel by neutron diffraction

Deformation Mechanisms and Work-Hardening Behavior of Transformation-Induced Plasticity High Entropy Alloys by in -Situ Neutron Diffraction

Real-Time in Situ Neutron Diffraction Investigation of Phase-Specific Load Sharing in a Cold-Rolled TRIP Sheet Steel

Effect of bainitic transformation temperature on the mechanical behavior of cold-rolled TRIP steels studied with in-situ high-energy X-ray diffraction

Effect of non-isothermal deformation of austenite on ferrite transformation behavior studied by in-situ neutron diffraction

Microstructures and Mechanical Properties of Hot-Rolled Nb-Microalloyed Trip Steels by Different Thermo-Mechanical Processes

Neutron Diffraction and Crystal Plasticity Analysis on Q&P Steel in Deformation

In-situ neutron diffraction investigation of two-stage martensitic transformation in a 13%Mn steel with serrated deformation

Effect of heat treatment on transformation-induced plasticity of economical Cr19 duplex stainless steel

Quantitatively evaluating respective contribution of austenite and deformation-induced martensite to flow stress, plastic strain, and strain hardening rate in tensile deformed TRIP steel

Dislocation Activities at the Martensite Phase Transformation Interface in Metastable Austenitic Stainless Steel: An In-situ TEM Study

Magnetic Ordering Suppressed Phase Transformation of a TRIP-HEA During Thermal Cycling

Investigation of the Microstructure, Mechanical Properties and Tensile Behavior of a Low Carbon Nickel-Manganese Dual-Phase Transformationinduced Plasticity Steel by Heavy Warm Rolling

In-Situ High-Energy Synchrotron X-Ray Diffraction Study of Micromechanical Behavior of Multiple Phases in Ni47ti44nb9 Shape Memory Alloy

Microstructure Control of Hot Rolled Trip Steel Based on Dynamic Transformation of Undercooled Austenite I. Prior Austenite Grain Size