Abstract:Abstract Shot peening processes are commonly used for improving the fatigue properties of steels. Shot peening introduces a compressive residual stress field in the near surface of steel, which can reduce or stop the growth of fatigue cracks and improve fatigue properties. This study experimentally investigated the effect of shot peening on the fatigue properties of 50CrV4 steel alloys with different artificial surface defects. Drilling tools were used to introduce different artificial defects with root radii of 0.585 mm and 0.895 mm on the surface of unpeened samples. The shot peening was applied to the drilled and undrilled samples. Scanning electron microscopy (SEM) observations, micro-hardness and X-ray diffraction residual stress measurements were conducted to analyse the characteristics of the shot-peened and unpeened samples. The results show that the shot peening leads to the transformation of the retained austenite to martensite in the near-surface microstructure. The hardness rates of the surface and near surface both increase by 8% after the shot peening. The peened samples exhibit compressive residual stresses with a high degree of isotropy in the near surface. The fatigue properties of samples were experimentally evaluated by conducting 3-point bending tests. The results indicate that the shot peening improves the fatigue life of drilled and undrilled samples. For the defects with the root radius of 0.895 mm, the shot peening leads to a 500% improvement in the fatigue life compared to unpeened samples regardless of defect depth. For the defects with the root radius of 0.585 mm, the improvement in fatigue life is 40% for the defect depth of 0.2 mm compared to unpeened samples. The improvement increases to 60% and 200% by increasing the defect depths to 0.4 mm and 0.6 mm. The fatigue properties are linked to the changes in the features of defects mainly caused by the deformation hardening and compressive residual stress after shot peening.

A numerical–analytical approach to predict the effects of shot peening on the fatigue performance of the nickel-based super alloy Waspaloy

A Study of Fatigue Mesoscopic Elasto-Plastic Properties of a Nickel-Base Superalloy by Instrumented Microindentation Measurements

Enhancing plain fatigue strength in aluminum alloys through shot peening: Experimental investigations and a strain energy density interpretation

Investigation of residual stress, stress relaxation and work hardening effects induced by shot peening on the fatigue life of AA 6005-T6 aluminum alloy

An analytical model for predicting residual stress in shot peening with strain energy method

Quantitative Study of High-Frequency Fatigue Hole-Edge Stresses in Nickel-Based Single-Crystal Superalloy

Cumulative Fatigue damage of AA7075-T6 under Shot Peening and Ultrasonic Surface Treatments

Turning/Shot peening of Nickel-based powder metallurgy superalloy: Effect on surface integrity and high-temperature low-cycle fatigue properties

Influence of shot peening on the microstructure and high-temperature tensile properties of a powder metallurgy Ni-based superalloy

Simulations of the effect of shot peening backstress on nanoindentation

Effects of shot peening and artificial surface defects on fatigue properties of 50CrV4 steel

Prediction of fatigue crack propagation behavior of AA2524 after laser shot peening

Prediction of fatigue crack growth and residual stress relaxations in shot-peened material

Effect of surface high density twin microstructure induced by shot peening on the fatigue behavior of Ti-6Al-4V

A study of shot peening and spinning rolling on fatigue of Al 7075 alloy samples

Nanoscale microstructural factors contributing to the improvement of the micromechanical wear properties of mechanical shot-peened nickel-based superalloys

Predicting the Effect of Surface Waviness on Fatigue Life of a Wire + Arc Additive Manufactured Ti-6Al-4V Alloy

Effect of Shot Peening on Surface Damage Evolution Behavior of Cu-19Ni Alloy

Numerical Simulation of Residual Stress Field Induced by Ultrasonic Shot Peening

Study on fatigue crack growth property of abrasive waterjet peened aluminum alloy

Prediction of the effect of shot peening residual stress on fretting fatigue behaviour