Abstract:The effect of rolling temperature on the incomplete recrystallization behavior and the relationship to mechanical properties in 0.06C–4Mn-1.2Cr (wt.%) steel was investigated. Three plates of experimental steel were produced by hot rolling at different temperatures and intercritical annealing processes in this study. The microstructure of experimental steels was examined by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The mechanical properties of test steel were examined by impact test and tensile test. Austenite reversion and cementite precipitation-dissolution was numerically simulated under the assumption of local equilibrium. With the decrease of hot rolling temperature from 1000 °C to 800 °C, the uniform equiaxed prior austenite grains microstructures changed to heterogeneous microstructures of laminated and ultrafine prior austenite grains arranged alternatively. The tensile and impact tests revealed that the medium manganese steels rolling at 800 °C had an excellent combination of mechanical properties. Elongation had a great relationship with retained austenite fraction and stability. The fractography of impact specimens was examined to explore the toughening mechanism of the micro-laminated steels. The steel with uniform equiaxed grain structure exhibited a relatively low tensile strength of 750 MPa and low elongation of ∼20% and an extremely poor low-temperature toughness of ∼40 J at −40 °C. An enhanced low-temperature toughness (∼233 J at −40 °C), as well as an improved tensile strength (823 MPa) and higher elongation of ∼40%, was obtained in the steel with heterogeneous microstructures. The content of austenite in heterogeneous microstructure is twice that in uniform equiaxed grain structure. And cementite dissolved more thoroughly in the heterogeneous microstructure. The high austenite content of heterogeneous microstructures enabled the steel to be significantly stronger and ductile, which contributed to the high tensile strength and elongation to some extent. It is concluded that the effect of interface decohesion resulted in the occurrence of delamination. And the high austenite content and delamination greatly improved the low-temperature toughness of experimental steel.

Microstructure and Mechanical Properties of As-cast 42CrMo Ring Blank During Hot Rolling and Subsequent Quenching and Tempering

Establishment of Thermal Ductile Fracture Criterion for As-Cast 42CrMo Steel and Its Application in Hot Ring Rolling Process

Effect of tempering on bonding characteristics of cross wedge rolling 42CrMo/Q235 laminated shafts

Effect of carbon content and microstructural refinement on the mechanical property of quenching-partitioning - tempering-treated steels

Effect of Finished Rolling Cooling Rate on Structure of Microalloy Non Quenched-Tempered Steel 34Mn2VN

Microstructure and mechanical properties of a low-carbon HDQ&P steel

Macrostructure, microstructure and mechanical properties evolution during 8Cr4Mo4V steel roller bearing inner ring forging process

Effects of Cooling after Rolling and Heat Treatment on Microstructures and Mechanical Properties of Mo–Ti Microalloyed Medium Carbon Steel

Effect of Heat Treatment on Structure and Properties of B Alloyed High Speed Steel for Rolling Mill Rolls

Effect of Hot Rolling on Microstructural Evolution and Wear Behaviors of G20CrNi2MoA Bearing Steel

Analysis of Microstructure and Mechanical Properties of 30CrMo Steel During Annealing After Cold Rolling

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy

Importance of cold rolling and tempering on the microstructure evolution, precipitation behavior and mechanical responses of 9Cr3Co3W1Cu ferritic/martensitic steel

Effect of Fibrous Macrostructure on Mechanical Properties, Anisotropy and Fracture Mechanism of Roller Bearing Ring

Microstructure Evolution and Coordinated Deformation of the 40Cr/Q345B Bimetallic Ring Blank at High Temperature

Effect of Cooling Process on Microstructure and Mechanical Properties of Hot Rolled 65Mn Steel

Cold Extrusion Deformation Behavior of Medium Carbon Steel after Quenching and Tempering

Work Hardening Behavior and Microstructure Evolution of a Cu-Ti-Cr-Mg Alloy during Room Temperature and Cryogenic Rolling

Effect of rolling temperature on microstructure and mechanical properties of medium manganese steel

Effect of Heavy Warm Rolling on Microstructures and Mechanical Properties of AISI 4140 Steel

Influence of Deep Cryogenic Treatment and Secondary Tempering on Microstructure and Mechanical Properties of Medium-Carbon Low-Alloy Steels