Abstract:Hollow fiber membranes fabricated via dry/wet phase inversion method usually have two dense skin layers,which will increase its resistance of mass transport as a support membrane. It is necessary that the dense skin layer of support membrane has been eliminated to improve separation performance of composite membrane. The excellent. chemical resistance of poly(vinylidene fluoride) (PVDF) to many acids and alkalis has made it as an attractive membrane material, and then it's often fabricated as porous hollow fiber membrane by phase inversion. In the process, the formation of the skin layer is due to the rapid exchange between solvent and coagulation, so many attempts have been made to slow it, so as to control the formation of the skin layer. In this paper, it has been found that the fabrication progress becomes unstable, and the membrane prepared has noncircular lumen, when the "weak" or "soft" coagulation is used. To increase the fabrication solution stability during membrane formation, dope viscosity was focused in this experiment. Dimethyl acetamide (DMAc) was used as solvent as well as internal coagulant, and the additives including LiCl, water and surfactant Span were chosen to investigate their effect oil the viscosity of the fabrication solution. The dope viscosity will greatly increase after adding LiCl, while the variety of dope viscosity is unconcerned in the fabrication solution concentration as adding water. The homogenization and stability of the fabrication solution are improved by adding Span,and the viscosity increases at the same time. Without increasing PVDF concentration, the stability of the nascent membrane was improved by increasing the fabrication viscosity. The PVDF hollow fiber membrane with the structure of single outer skin layer and finger-like pore through the cross-section, has been successfully fabricated. The mean pore radius and water flux of the single skin hollow fiber membrane were greatly improved.

A Pathway to Fabricate Hollow Fiber Membranes with Isoporous Inner Surface

Fabrication of Hydrophilic and Sponge-Like PVDF/brush-like Copolymer Blend Membranes Using Triethylphosphate As Solvent

Fabrication of High-Flux PTFE Hollow Fiber Membranes Through Nonionic Surfactant Infiltration Coupled with Mussel-Inspired Chemistry Coating

A Comprehensive Review of Hollow-Fiber Membrane Fabrication Methods across Biomedical, Biotechnological, and Environmental Domains

Influence of Dope Viscosity on the Fabrication of Pvdf Hollow Fiber Membranes with Single Skin Layer

Experimental And Numerical Analyses On The Poly(Lactide-Co-Glycolide) Hollow Fiber Membranes

A Design of Composite Hollow Fiber Membranes with Tunable Performance and Reinforced Mechanical Strength

Fabrication of a Novel PS4VP/PVDF Dual-Layer Hollow Fiber Ultrafiltration Membrane

High performance zeolite NaA membranes synthesized on the inner surface of zeolite/PES–PI blend composite hollow fibers

Fabrication of ZIF-8 Membranes on Dual-Layer ZnO-PES/PES Organic Hollow Fibers by In-Situ Crystallization

Microfiber Aligned Hollow Fiber Membranes from Immiscible Polymer Solutions by Phase Inversion

Fabrication of Transferable Perforated Isoporous Membranes on Versatile Solid Substrates Via the Breath Figure Method

Tailoring Nonsolvent-Thermally Induced Phase Separation (N-TIPS) Effect Using Triple Spinneret to Fabricate High Performance PVDF Hollow Fiber Membranes

3D-printed rotating spinnerets create membranes with a twist

Structure formation and characterization of PVDF hollow fiber membranes by melt-spinning and stretching method

Hollow fibers for nanofiltration/organic solvent nanofiltration

Novel Polyamide-Imide/cellulose Acetate Dual-Layer Hollow Fiber Membranes for Nanofiltration

A facile and scalable fabrication procedure for PVDF-PDA/PEI/SiO2 hollow fiber composite ultrafiltration membranes: Integration of co-deposition and cross-linking

Fabrication of PS/PVDF-HFP Multi-Level Structured Micro/Nano Fiber Membranes by One-Step Electrospinning

Hollow Fiber Polyimide Membranes Prepared in a Triple Orifice Spinneret: Effect of a Reduced Water Activity in the Bore Fluid on the Gas Separation Performance

Facile Fabrication of Reinforced Homoporous MF Membranes by in Situ Breath Figure and Thermal Adhesion Method on Substrates