Abstract:The objective of this work is a dilatometric study of Al + 0.1% of multiwall carbon nanotubes nanocomposite material (NCM) in three directions: X - parallel to the rolling direction; Y - perpendicular to the rolling direction and (Z) perpendicular to the ribbon plane. NCM specimens were made in the form of a 0.1-mm-thick ribbon. The temperature range used for measurements was 20°C to 600°C. The obtained results show that presence of nanotubes affects the thermal expansion coefficient (TEC) measured in different directions. αx(T) and αy(T) - TEC plots as a function of temperature along X and Y directions, respectively - have substantially the same shape and overlap in the area of 400°C. The expansion along X-axis becomes greater than along Y-axis below this temperature value. It is clear that the coefficient αz(T) is lower than αx(T) and αy(T) over the entire temperature range. The expansion along Z-axis is smaller compared to that along X- and Y-axes. This behaviour suggests that there is a strong interatomic interaction along this direction (Z). αz(T) becomes monotonous and constant and is equal to 8 × 10(-6)°C(-1) at temperatures above 300°C. Such order of magnitude had not been obtained in earlier studies of aluminium alloys. The obtained TEC shows high anisotropy, which grows with the increase of temperature. The heat flow (differential scanning calorimetry, (DSC)) of Al + 0.1% carbon nanotubes (CNT) NCM is more intense compared to that of pure aluminium produced in similar conditions. The two representative curves have similar shape and are almost entirely overlapped. The thermogravimetry results confirm those of DSC. The Raman spectrum of this nanomaterial shows that intensity of G and D bonds is significantly increased compared to that of the pure material. The infrared diagram also confirms that in this case the mentioned bonds are more intensive NCM. The tensile strength measurements (σB) of the studied NCM also demonstrate that its value increases from 140 ± 10 MPa for Al without nanotubes to 200 ± 10 MPa for NCM.

Thermal Analysis of Copper-Titanium-Multiwall Carbon Nanotube Composites

Influence of Embedded-Carbon Nanotubes on the Thermal Properties of Copper Matrix Nanocomposites Processed by Molecular-Level Mixing

Thermal analysis of Al + 0.1% CNT ribbon

Sintering And Thermal Properties Of Multiwalled Carbon Nanotube-Batio3 Composites

Influences of Carbon Nanotubes on Performance of W-Cu Composite Materials

Thermomechanical analysis of the effect of contact forces in heat conduction of composite materials through multiscale contact finite element modeling

Thermal conductivities of alumina-based multiwall carbon nanotube ceramic composites

Influence of carbon nanotubes on thermal expansion coefficient and thermal buckling of polymer composite plates: experimental and numerical investigations

Thermal Analysis of Ni-Cu Alloy Nanocomposites Processed by Sand Mold Casting

Evaluation of tribo-mechanical measurements and thermal expansion of Cu-based nanocomposites reinforced by high strength hybrid ceramics

Thermal Expansion Behaviors of Aluminum Composite Reinforced with Carbon Nanotubes

Preparation and elevated temperature compressive properties of multi-walled carbon nanotube reinforced Ti composites

The Specific Heat and Effective Thermal Conductivity of Composites Containing Single-Wall and Multi-Wall Carbon Nanotubes.

A Study on the Thermal Conductivity of Multiwalled Carbon Nanotube/Polypropylene Composite

Differential Multi-probe Thermal Transport Measurements of Multi-walled Carbon Nanotubes grown by Chemical Vapor Deposition

Studying the effect of design microscale factors on the thermoelastic response of carbon nanotube-reinforced metal nanocomposites using the finite element micromechanics method

The Thermal and Mechanical Properties of a Polyurethane/multi-Walled Carbon Nanotube Composite

Densified Multiwalled Carbon Nanotubes–titanium Nitride Composites with Enhanced Thermal Properties

Mechanical and Conductive Properties of Cu Matrix Composites Reinforced by Oriented Carbon Nanotubes with Different Coatings

Thermal Properties of Composite Materials Based on the Powder Systems “Copper–CNTs”

Processing and Thermal Properties of Multiwall Carbon Nanotube/Bismuth Antimony Telluride Composites for Nuclear Energy Applications