Abstract:The UK's National Joint Registry (NJR) and the American Joint Replacement Registry (AJRR) of 2022 revealed that total hip replacement (THR) is the most common orthopaedic joint procedure. The NJR also noted that 10-20% of hip implants require revision within 1 to 10 years. Most of these revisions are a result of aseptic loosening, dislocation, implant wear, implant fracture, and joint incompatibility, which are all caused by implant geometry disparity. The primary purpose of this review article is to analyze and evaluate the mechanics and performance factors of advancement in hip implants with novel geometries. The existing hip implants can be categorized based on two parts: the hip stem and the joint of the implant. Insufficient stress distribution from implants to the femur can cause stress shielding, bone loss, excessive micromotion, and ultimately, implant aseptic loosening due to inflammation. Researchers are designing hip implants with a porous lattice and functionally graded material (FGM) stems, femur resurfacing, short-stem, and collared stems, all aimed at achieving uniform stress distribution and promoting adequate bone remodeling. Designing hip implants with a porous lattice FGM structure requires maintaining stiffness, strength, isotropy, and bone development potential. Mechanical stability is still an issue with hip implants, femur resurfacing, collared stems, and short stems. Hip implants are being developed with a variety of joint geometries to decrease wear, improve an angular range of motion, and strengthen mechanical stability at the joint interface. Dual mobility and reverse femoral head-liner hip implants reduce the hip joint's dislocation limits. In addition, researchers reveal that femoral headliner joints with unidirectional motion have a lower wear rate than traditional ball-and-socket joints. Based on research findings and gaps, a hypothesis is formulated by the authors proposing a hip implant with a collared stem and porous lattice FGM structure to address stress shielding and micromotion issues. A hypothesis is also formulated by the authors suggesting that the utilization of a spiral or gear-shaped thread with a matched contact point at the tapered joint of a hip implant could be a viable option for reducing wear and enhancing stability. The literature analysis underscores substantial research opportunities in developing a hip implant joint that addresses both dislocation and increased wear rates. Finally, this review explores potential solutions to existing obstacles in developing a better hip implant system.

Influence of proximal femoral morphology on osteointegration of the AMIS uncemented femoral stem in modern hip arthroplasty

Theoretical analysis of changes in femoral stresses after total hip arthroplasty]

Mid-term results of total hip arthroplasty using a novel uncemented short femoral stem with metaphyso-diaphyseal fixation

Improving planning and post-operative assessment for Total Hip Arthroplasty

Advancement in total hip implant: a comprehensive review of mechanics and performance parameters across diverse novelties

Current methods of preventing aseptic loosening and improving osseointegration of titanium implants in cementless total hip arthroplasty: a review

Evaluation of Proximal Femoral Bone Mineral Density in Cementless Total Hip Arthroplasty: A 3-Arm Prospective Randomized Controlled Trial

Differences between two sequential uncemented stem sizes in total hip arthroplasty: A comparative biomechanical study and potential clinical implications

The effect of femoral neck osteotomy on femoral component position of a primary cementless total hip arthroplasty

The assessment of implant shape-dependent failure mechanisms in primary total hip arthroplasty using finite element analysis

A Comparison of Clinical Outcomes of a Straight and an Anatomical Uncemented Stem

Does femoral stem choice influence fracture type or incidence for direct anterior approach total hip arthroplasty?

Influence of the angle between tibial and prosthesis mechanical axes on tibial bone remodeling in total knee arthroplasty

Total Hip Arthroplasty Combined with Proximal Femoral Reconstruction Effectively Treats Severe Hip Deformities: A Novel Osteotomy Technique

The Influence of Dorr Type and Femoral Fixation on Outcomes Following Total Hip Arthroplasty for Acute Femoral Neck Fractures: A Multicenter Study

Offset Considerations in Total Hip Arthroplasty

Three-dimensional femoral morphology in Hartofilakidis type C developmental dysplastic hips and the implications for total hip arthroplasty

The Proximal and Distal Femoral Canal Geometry Influences Cementless Stem Anchorage and Revision Hip and Knee Implant Stability

Middle-term outcome and complications after primary total hip arthroplasty using a contemporary titanium tapered wedge cementless femoral stem

Mid-term outcomes of total hip arthroplasty in patients younger than 30 years

Long-term clinical results and patient satisfaction of a metaphyseal-engaging anatomic cementless femoral component in total hip arthroplasty