Abstract:In this study, the effect of heat treatment and yttrium additions on the microstructure, mechanical properties, and tribological behavior of Al-15% Mg2Si cast composites was investigated. The microstructural study revealed the presence of both primary and secondary Mg2Si phases in all composite specimens and also Y-containing intermetallics (Al2Y phases) at higher concentrations. It was also found that Y addition does not change the size and morphology of primary Mg2Si particles considerably, but the pseudo-eutectic Mg2Si changed from a flake-like morphology to fine fibrous or rod-like one. The results show that proper content of Y additions can reduce the amount of Mg2Si phase through dissolving it into the matrix, lead to the precipitation of Al2Y phase and improve the mechanical properties. Modified composites with 0.5% Y exhibited an ultimate tensile strength (UTS) of 290 MPa with an elongation of 4.3%. After exposing the composite to solution treatment at 520 °C for 4 h, the tensile strength of the composite continuously increased with the increase of Y content, and reached the maximum at 1% Y. The maximum UTS and elongation at room temperature for the heat-treated composites are 294 MPa and 7.4%, respectively. In the cast specimen, fracture surfaces are covered by packets with coarse steps, suggesting a brittle mode of failure. Modified composites with 0.5 wt.% Y contain several cracked particles together with a few decohered primary Mg2Si particles. In solution heat-treated state, dimples present at the fracture surface are rather coarse but homogenous, showing a semi-ductile mode of fracture. Wear test results showed that the wear resistance of all specimens increases with the addition of Y up to 0.3 wt.%. Scanning electron microscopic observations of the worn surfaces revealed that the dominant wear mechanism was abrasive wear accompanied by some delamination wear mode.

The effect of yttrium on the microstructure and wear and mechanical properties of Al-20%Sn

The Effects of Yttrium Element on Microstructure and Mechanical Properties of Mg–5 Wt.% Zn–2 Wt.% Al Alloy

Effect of Yttrium Addition on Microstructure and Mechanical Properties of Sr-Modified Low-Si Cast Aluminum Alloy

Effect of Yttrium on Microstructure and Mechanical Properties of ZAlSi7Mg Alloy

The effect of yttrium on the microstructure and mechanical of ZL025A alloys

Effect of Y on Microstructure and Mechanical Properties of A Ti Alloy

Effects of Yttrium on Microstructure and Properties of TiAl Alloy

Effects of Yttrium on Microstructures and Properties of Ti-17Al-27Nb Alloy

The Effects of Yttrium on the Mechanical Alloying of AlW System

Effects of Yttrium on Microstructure and Mechanical Properties of Mg-6Al Magnesium Alloy

Effects of yttrium additions on microstructures and mechanical properties of cast Al-Cu-Mg-Ag alloys

Influence of Yttrium on Microstructure, Mechanical Properties and Deformability of Ti–43Al–9V Alloy

Effects of yttrium on microstructure and mechanical properties of hot-extruded Mg–Zn–Y–Zr alloys

Effect of Yttrium Addition on Microstructures and Room Temperature Tensile Properties of Ti-47 Al Alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Effects of Yttrium on Microstructure and Mechanical Properties of In Situ (Al2O3+Al3Zr)p/A356 Composites

Mechanical and Tribological Characterization of Al-Mg2Si Composites after Yttrium Addition and Heat Treatment

Microstructural evolution and mechanical property of Al–Zr and Al–Zr–Y alloys

Effects of Minor Yttrium Addition on Microstructure, Mechanical Properties and Hot Workability of Nb or V Containing TiAl Alloys

Effects of Yttrium and Heat Treatment on the Microstructure and Tensile Properties of Al–7.5Si–0.5Mg Alloy

Corrosive wear resistance of Mg-Al-Zn alloys with alloyed yttrium