Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

Influence of tensile strength on the load bearing capacity of tall reinforced masonry walls

Seismic Performance of Reinforced Concrete Squat Walls with Embedded Cold-Formed and Thin Walled Steel Truss

Simulation Of Collapse Process Of Masonry Walls Based On Expanded Discrete Element Method

Finite element-based reliability analysis of reinforced concrete masonry walls under eccentric axial loading considering slenderness effects

Experimental and numerical evaluation of a U-shaped thin lightly reinforced concrete wall tested under cyclic loading

Seismic behavior and modeling of T‐shaped reinforced concrete walls under high axial force ratios

Analytical modeling of masonry load-bearing walls

Coupled Axial Tension-Shear Behavior of Reinforced Concrete Walls

Seismic behavior of reinforced concrete slender walls subjected to variable axial loads

Direct Strut-and-Tie Model for Ultimate Shear Strength of Reinforced Concrete Structural Walls

Influence of Axial Stress on Shear Response of Reinforced Concrete Elements

Shear Behaviour of Reinforced Concrete Structural Walls with Eccentric Openings under Cyclic Loading: Experimental Study

Seismic behavior of reinforced concrete shear walls subjected to high axial loading

Effects of aspect ratios and vertical loads on in-plane seismic behavior of unreinforced masonry walls: A numerical simulation

The Effects of Applied Axial Stress on Lateral Bearing-Load Capacity for Fully Grouted Reinforced Concrete Masonry Shear Walls

Experimental Study of Shear-Critical Reinforced-Concrete Shear Walls under Tension-Bending Shear-Combined Cyclic Load

Elasto-Plastic Analysis Of Reinforced Concrete Shear Wall With Openings Using A Macro Model

Theoretical Method for Predicting the Failure Mode of Reinforced Concrete Shear Walls Subjected to Axial Tension and Cyclic Lateral Loads

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

Seismic Behavior of Slender Prestressed Reinforced Concrete Short-Leg Walls

In-Plane Shear Behavior of Unreinforced Masonry Wall Strengthened with Bamboo Fiber Textile-Reinforced Geopolymer Mortar