Abstract:Atomic layer deposition (ALD) is a highly important technology to fabricate nickel and nickel compound thin films. The quality of the ALD films relies much on the surface chemistry reactions involved in the ALD process. Aiming to achieve high-quality ALD films, a careful surface chemistry study is carried out in this work to investigate the surface thermolysis behavior of an amidinate-type nickel precursor, bis(N,N'-di-tert-butylacetamidinato)nickel(II) (Ni(amd)(2)). Using the in situ technique of X-ray photoelectron spectroscopy, this work reveals a number of implications which are important for the engineering of the ALD processes. The Ni(amd)(2) precursor is shown to be reactive to the SiOx surface even at room temperature, which suggests a good suitability for low-temperature ALD. The surface amidinate moiety is found to decompose at 250 degrees C, which suggests the limitation of Ni(amd)(2) for high-temperature ALD. On the other hand, the byproduct of the surface reaction, amidine, can be adsorbed on the surface at low temperature, which might be trapped in the deposited film, inducing carbon and nitrogen impurities. Therefore, if the goal is to achieve a low impurity, a relatively higher deposition temperature (e.g., at 150-200 degrees C) would be favored. To further demonstrate the important value of the above implications from the thermolysis study, an example of the ALD of NiO is investigated experimentally. Indeed, the NiO films can be successfully deposited at an ever-low temperature of 90 degrees C, and increasing the deposition temperature to 200 degrees C can eliminate the accumulation of carbon and nitrogen impurities at the film-substrate interface, whereas the deposition at 250 degrees C leads to drastic increase in impurities, likely owing to the thermal decomposition of the surface amidinate moiety. All these experimental findings are well consistent with the implications from the surface thermolysis study, which highlights the important value of this surface thermolysis approach for rational ALD process engineering. Given the similarity and broad use of the amidinate-type metal precursors, the results reported herein should also be of significant value for many other ALD processes.

A molecular dynamics study of nickel vapor deposition: Temperature, incident angle, and adatom energy effects

Thermal and Stress Impacts on Vacancy Diffusion Through Atomistic Simulations

Kinetic Monte Carlo Study of Void Distribution in Nickel Thin Film by Physical Vapor Deposition

Effects of Incident Angle on Microstructure of Ni Thin Film Deposited by PVD

Atomic Simulation of Void Location Effect on the Void Growth in Nickel-Based Single Crystal

Theoretical Study on Thin-Film Formation by Parallel Molecular Dynamics Simulation

Study on Machining Single-Crystal Nickel by Molecular Dynamics Simulation

Atomistic Simulation Analysis of the Effects of Void Interaction on Void Growth and Coalescence in a Metallic System

Orientation Effects on the Tensile Properties of Single Crystal Nickel with Nanovoid: Atomistic Simulation

Molecular Dynamics Simulation of Dislocation Plasticity Mechanism of Nanoscale Ductile Materials in the Cold Gas Dynamic Spray Process

Atomistic Mechanisms of Binary Alloy Surface Segregation from Nanoseconds to Seconds Using Accelerated Dynamics

Molecular dynamics simulations of physical vapor deposition

Research on the Nanometric Machining of a Single Crystal Nickel Via Molecular Dynamics Simulation

Molecular dynamics simulation of single crystal Nickel nanometric machining

A Molecular Dynamics Study of Ag-Ni Nanometric Multilayers: Thermal Behavior and Stability

Atomistic Study of Deposition Process of Al Thin Film on Cu Substrate

Surface Thermolytic Behavior Of Nickel Amidinate And Its Implication On The Atomic Layer Deposition Of Nickel Compounds

Anomalous Approach to Thermodynamic Equilibrium: Structure Formation of Molecules after Vapor Deposition

Molecular Dynamics Study on the Interactions of 1/2[110] Edge Dislocations with Voids and Ni3Al Precipitates in FCC Ni

Vaporization of Ni, Al and Cr in Ni-Base Alloys and Its Influence on Surface Defect Formation During Manufacturing of Single-Crystal Components

Formation mechanism and microstructure characterization of nickel-aluminum intertwining interface in cold spray