Abstract:Despite the many articles about activated carbon with different precursors in adsorption process, no in-depth research has been carried out to understand the causes of the difference in surface adsorption characteristics of activated carbon with different precursors and different activation processes. In this work, the ability of two active carbon adsorbents made of walnut shell and peach kernel by two chemical and physical methods (totally 4 different types of activated carbon) in treatment of oily wastewater including diesel, gasoline, used oil or engine lubricant has been compared. The results show that the chemical activated peach carbon active with 97% hardness has provided the highest hardness and physical activated walnut carbon active has obtained the lowest hardness value (87%). It is also found that peach activated carbon has a higher iodine number than walnut activated carbon, and this amount can be increased using chemical methods; Therefore, the highest amount of Iodine Number is related to Peach activated carbon that is made by chemical method (1230 mg/g), and the lowest amount of iodine number is seen in walnut activated carbon that is made by physical method (1020 mg/g). moreover, the pore diameter of physical activated carbon is lower than chemical activated carbon in all cases. So that the pore diameter of chemical activated peach carbon active is equal to 22.08 μm and the measured pore diameter of physical activated peach carbon active is equal to 20.42 μm. These values for walnut are obtained as 22.74 μm and 21.86 μm, respectively. Furthermore, the temperature and pH effects on the adsorption of different synthesized oily wastewater was studied and it was found that a decrease in adsorption can be seen with an increase in temperature or decreasing the pH value, which can be referred to this fact that the process of adsorption is an exothermic process. Finally, to analyze the compatibility of adsorption isotherms with experimental data and to predict the adsorption process, three different isotherms named Langmuir, Temkin, and Freundlich isotherms were applied and their parameters were correlated. The correlation results show that the Langmuir isotherm had the best correlation in all cases compared to the Freundlich and Temkin isotherms, based on the correlation coefficient, and the calculated R 2 values which was greater than 0.99 in all the studied cases.

Investigation of synthesis and sonocatalytic performance of activated carbon-supported catalysis systems

Investigation on the Sonocatalytic Degradation of Acid Red B in the Presence of Nanometer TiO2 Catalysts and Comparison of Catalytic Activities of Anatase and Rutile TiO2 Powders.

Activation of Peroxymonosulfate by CoS2 Loaded Air-Laid Cloth for Rapid Degradation of Organic Pollutants in a Shallow Continuous Flow Reactor

Study of Catalysts’ Influence on Photocatalysis/Photodegradation of Olive Oil Mill Wastewater. Determination of the Optimum Working Conditions

Detection and analysis of reactive oxygen species (ROS) generated by nano-sized TiO2 powder under ultrasonic irradiation and application in sonocatalytic degradation of organic dyes.

Fitting Biochars and Activated Carbons from Residues of the Olive Oil Industry as Supports of Fe- Catalysts for the Heterogeneous Fenton-Like Treatment of Simulated Olive Mill Wastewater

In situ preparation of TiO2/f-MWCNT catalyst using Pluronic F127 assisted sol-gel process for sonocatalytic degradation of methylene blue

Preparation of a silver ferrite-assisted tungsten oxide nanocomposite for efficient sonocatalytic degradation of organic pollutants activated by PMS followed by toxicity evaluation

Application of magnetic activated carbon as a catalyst in catalytic ozonation process (COP) for removal and mineralization of humic acid from aqueous solution

Sonocatalytic Activity of Porous Carbonaceous Materials for the Selective Oxidation of 4-Hydroxy-3,5-dimethoxybenzyl Alcohol

Simultaneous Removal of Multipollutants (vocs/no/so2) by Catalytic Ozonation Coupled with Wet Scrubbing Technology: from the Laboratory to Industrial Testing

Sol-Gel Preparation and Characterization of Activated Carbon Supported TiO_2 Photocatalyst

An innovative method to remove phenols from olive mill wastewater using heterogeneous modified polyacrylonitrile (PAN) catalyst

Thermodynamic and structural investigation of oily wastewater treatment using peach kernel and walnut shell based activated carbon

Catalytic peroxidation of winery wastewater contaminants using activated carbon-supported magnetite nanoparticles

Integrated Ozonation Ni-NiO/Carbon/g-C3N4 Nanocomposite-Mediated Catalytic Decomposition of Organic Contaminants in Wastewater under Visible Light

Preparation and characterization of activated carbons from Lemon Pulp for oxytetracycline removal

Advanced degradation of organic pollutants using sonophotocatalytic peroxymonosulfate activation with CoFe2O4/Cu- and Ce-doped SnO2 composites

Strontium titanate nanocubes assembled on mesoporous graphitic carbon nitride (SrTiO3/mpg-C3N4): Preparation, characterization and catalytic performance

"Synthesis and characterization of mesoporous V-Mo-MCM-41 nanocatalysts: Enhancing efficiency in oxalic acid synthesis"

Study on Catalyst of Catalytic Wet Oxidation of Sorbic Acid Industrial Wastewater