Abstract:Highlights • A dual phase β+α Mg-Li alloy was fabricated as reducing the Li content. • The dispersed α-Mg phases mitigate the dimension and distribution of eutectic I-Phase along grain boundaries. • The dual phase Mg-Li alloy exhibits enhanced ductility (elongation (EL) = 17.8 %) due to the improved deformation compatibility. • The continuity of slip between α-Mg and β-Li on plane pairs of {123}Li-{ 112 ̄2 }Mg and {112}Li-{ 112 ̄2 }Mg assures the deformation compatibility across interfaces. • Two strengthening mechanisms, nanoscale B2 (Li, Mg) 3 Zn-type precipitates and the microscale I-phase, are characterized. Mg-Li alloys with high lithium concentrations possess a lightweight body-centered cubic (BCC) matrix structure (β-Li). Interspersed eutectics (primarily the reticulated I-phase) often form along phase boundaries (PBs) and grain boundaries (GBs) which strengthen the alloy but cause the loss of ductility due to the brittle behavior of I-phase. By modifying the Li content, we fabricated the (β+α) biphase Mg-Li alloy in which the α-Mg phase with a hexagonal close-packed structure (HCP) is embedded in β-Li matrix, significantly increasing interface density. The high-density interfaces mitigate the distribution and dimension of the I-phase along GBs and PBs. The alloy exhibits enhanced ductility (elongation (EL) = 17.8 %) compared with the alloy without the α-Mg phase (EL = 5.1 %). Structural characterizations unveil the strengthening mechanism of the nanoscale B2 (Li, Mg) 3 Zn-type precipitates in conjunction with the microscale I-phase. The (Li, Mg) 3 Zn nanophases augment the yield and ultimate tensile strength of the alloy without a discernible compromise in ductility, predominantly due to gliding dislocations cutting through the precipitates. In contrast, the microscale I-phase presents a formidable barrier to dislocation motion, facilitating dislocation pileups at interfaces and culminating in diminished ductility across the interface. In-situ stretching techniques were employed to scrutinize the microstructural evolution of alloys during tensile deformation, elucidating that the deformation compatibility of alloys correlates with the average size of the I-phase and their distribution along GBs and PBs. Corresponding to the orientation relationship (OR) between the α-Mg and β-Li phases {110}Li//{0001}Mg and < 1 ̄11 >Li //< 112 ̄0 >Mg, the slip continuity between α-Mg and β-Li on plane pairs of {123}Li-{ 112 ̄2 }Mg and {112}Li-{ 112 ̄2 }Mg assures the deformation compatibility through facilitating the deformation across interfaces. Simultaneously, during the stretching process, the dispersed I-phase instigates the emergence of sporadic microcracks, indicating gradual damage evolution. These discoveries offer novel insights into achieving exceptional strength-ductility amalgamations in Mg-Li alloys through microstructural adjustments.

Effect of the Al–Si eutectic on the microstructure and corrosion behavior of the single-phase Mg alloy Mg–4Li

Influence of Al-Si eutectic alloy on the mechanical behaviors and microstructure feature of ultralight dual-phase Mg-8Li-x(Al-12.6 Si) alloys

Microstructure and corrosion behavior of as-homogenized and as-extruded Mg−xLi−3Al−2Zn−0.5Y alloys (x=4, 8, 12)

Corrosion and Characterisation of Dual Phase Mg–Li–Ca Alloy in Hank’s Solution: the Influence of Microstructural Features

Influence of Si contents on the microstructure and corrosion resistance of the Zn−Al−Mg−Si alloys

Effect of Al on Microstructure and Mechanical Properties of Mg-10Li-3Zn-1Y Alloys

Effects of Al Concentration on Microstructure and Mechanical Properties of Mg-xAl-1Zn-1Si Alloy

Study on Strengthening and Toughening of Mechanical Properties of Mg-Li Alloy by Adding Non-Rare-Earth Elements Al and Si

Effect of Li addition on microstructure and mechanical properties of Al – Mg – Si alloy

Corrosion Mechanism Associated with Mg2Si and Si Particles in Al–Mg–Si Alloys

Formation of Phases and Microstructures in Al-8Si Alloys with Different Mg Content

Comparison of Microstructure, Mechanical Property, and Degradation Rate of Mg–1Li–1Ca and Mg–4Li–1Ca Alloys

Effect of Iron-Rich Intermetallic and Eutectic Si Accumulation on Al-Si-Mg Alloy

Effect of Li on Microstructures and Properties of Al-3.5Cu-1.5Mg Alloy

Microstructure and Corrosion Resistance of Solidified Zn-Al-Mg Alloys

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy

Influence of enhanced Li content on the as-cast eutectic phase features and the evolution during homogenization of Al-Cu-Li alloys

Precipitate microstructures, mechanical properties and corrosion resistance of Al-1.0 wt%Cu-2.5 wt%Li alloys with different micro-alloyed elements addition

Effect of Al Addition and Heat Treatment on the Microstructures and Corrosion Resistance of Mg-Cu Alloys

Enhancing the ductility of cast Mg-Li alloys via dispersed α-Mg phase mitigating the dimension and distribution of interspersed eutectics along grain boundaries

Influence of Mg content on ageing precipitation behavior of Al-Cu-Li-x alloys